¡From the projection distance table (page 10) and dimensions (page 11), confi rm the screen size and the | English | |||||||||||||||||||||||||||
distance between the projection surface and wall plate. |
|
|
|
|
|
|
| |||||||||||||||||||||
¡The wall plate and the projection surface have different vertical center lines. |
|
|
|
| ||||||||||||||||||||||||
Align the CTR line (printed on the template sheet) with the center line of the projection surface as shown in | ||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||
the illustration. |
|
|
|
|
|
|
|
| ||||||||||||||||||||
¡Confi rm where the beams are within the wall, | 0.27 inch |
| 0.65 inch |
| ||||||||||||||||||||||||
and shift the position vertically or left and | (68 mm) |
| (164 mm) |
| ||||||||||||||||||||||||
right as necessary. |
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Unit: inch (mm)
| 0.51 x 1.30 | 1.06 |
| 1.77 x 3.15 |
| (27) | (45 × 80) | ||
| (13 × 33) | |||
|
| |||
|
|
| ||
5.15 | (135) |
|
| 6.77 (172) |
|
|
| 8.82 (224) |
|
|
|
| 15.99 (406) |
|
|
|
| 18.23 (463) |
|
WARNING
¡When you install the projector to the wall with the setting plate, the wall needs to be strong enough to hold the projector and the setting plate. Confi rm the weight of the pro- jector and the setting plate before installation, and check the strength of the wall.
If the wall is not strong enough, reinforce the wall before installation.
(Example) The combined mass of the projector
¡Use commercially available anchors.
¡Use M12 nuts, bolts and washers (26 mm outside diameter). Nuts and bolts smaller than M12 could cause the setting plate to fall. (The wall plate must be secured in at least four places.)
¡Sanyo takes no responsibility for any damages or injury caused by incorrect installation.
4
10.9.8 11:21:13 AM