Grizzly Setup, UnpackingAssembly, Model T23096 Inventory Figure, Air supply setup tips

Page 8

SECTION 2: SETUP

UnpackingAssembly

Your tool was carefully packaged for safe transportation. Remove the packaging materials from around your tool and inspect it. If you discover the tool is damaged, please immediately call Customer Service at (570) 546-9663 for advice.

Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult. When you are completely satisfied with the condition of your shipment, inventory the contents.

If any non-proprietary parts are missing (e.g., a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store.

Inventory

Model T23096 Inventory (Figure 2)

 

A.

Die Grinder

1

B. Quick Disconnect Air Fitting

1

C.

Bottle for Oil

1

D.

Spindle Wrench 12"

1

E.

Collet Nut Wrench 1116"

1

A

 

B

 

 

 

D

C

 

 

 

 

E

Figure 2. Inventory.

-6-

To assemble the grinder:

1.Remove the plastic plug from the grinder air inlet.

2.Apply pipe sealant on the quick disconnect fitting threads, and install the fitting into the grinder air inlet.

3.Insert the shank of the desired grinding bit into the collet until it bottoms, and tighten the collet nut (see Figure 1) using the spindle and collet wrenches.

4.Release the trigger lock, depress the trigger, place a few drops of air tool oil into the air inlet, and release the trigger. The grinder is ready for use.

Air supply setup tips:

If the air hose is longer than 25-feet, increase the air pressure to 100 PSI to compensate for air flow restriction.

For consistent air flow, use air hoses with an inside diameter of 38" or larger.

To eliminate air system moisture and maintain automatic lubrication, install a main or in-line filter water separator as far as possible from the air compressor, but before any automatic in-line oiler. See examples in Figure 3.

In-Line

 

 

Quick-Disconnect

Steel

Oiler

 

 

 

Fittings

 

Air Piping

Filter

 

 

 

Male

Female

 

Regulator

 

 

 

 

 

 

 

(Optional)

 

 

 

 

 

 

 

Your

 

 

 

 

 

 

Compressor

 

 

 

 

 

 

 

Tool

 

 

 

 

 

 

 

Lead-In Hose

 

Automatic

 

Filter

 

 

Water

(Optional)

 

 

 

 

 

Oiler

 

Separator

 

 

Main Air

Air

 

 

 

 

 

 

Supply Hose

 

Regulator

 

Figure 3. Typical air supply system.

Model T23096 Industrial 14" Die Grinder

Image 8
Contents Industrial 1⁄4 DIE Grinder Page Table of Contents Safety Safety Instructions for Pneumatic ToolsBefore Operating This Equipment Mation about proper operation of the equipmentAdditional Safety Instructions for Pneumatic Die Grinders Foreword Contact Info SpecificationsIntroduction Identification Setup UnpackingAssemblyAir supply setup tips InventoryTo complete a typical cutting or grinding operation OperationsOperation Overview T20887 T20881 G6261 AccessoriesG8210-50-Pc. Stone Set H3105-Clamp Style Magnifying Lamp G7870 G7872 G7871 G7866 T21767G7867Periodically as required MaintenanceBefore and after each use Service TroubleshootingPort Model T23096 Industrial 1⁄4 Die Grinder Main Parts Diagram Main Parts List PartsWarranty