Assembly, Operating Instructions | Bosch Power Tools 1506 specs

BM 1609929Y01 05-10:BM 1609929Y01 05-10 5/10/10 9:10 AM Page 8

Assembly

BLADE INSTALLATION AND ADjUSTMENT Correct clearances must be maintained for proper functioning of the tool and for clean cutting. To avoid accidents, always disconnect the tool from the power source while making adjustments

Insert lower shear blade in groove provided in the footplate and upper shear blade in groove of plunger. Finger tighten screws (A) and (B). Do not omit lock washer and flat washer for screw (A). When adjusting the lower blade, be sure plunger is at the bottom of the stroke.

UPPER BLADE – First bring the plunger into the top position by moving the fan blade with the pin provided. Move the upper blade until the vertical clearance between the blades is 1/64". After tightening the upper blade screw (A), tighten the setting screw with the pin provided.

The height adjustment of the upper blade is independent of the thickness of the sheet metal to be cut. For soft and malleable materials it must, however, in some cases be set lower, while for hard and brittle materials, it may be slightly increased.

LOWER BLADE – The horizontal clearance is directly related to the thickness of the metal being cut. Adjust clearance with the blade adjustment screw, then tighten the lower blade with the lower blade screw (B).

The clearance gap of the material being cut can be obtained with the help of the table provided below.

The recommended clearances are based on standard sheet metal specifications. For soft and tough materials (i.e. aluminum), reduce the recommended clearance. For hard and brittle materials (i.e. special stainless steel), increase the recommended clearance.

Gauge		Maximum Clearance
8	(.164")	.032 (0.8mm)
10	(.134")	.024 (0.6mm)
12	(.104")	.020 (0.5mm)
14	(.074")	.016 (0.4mm)
16	(.059")	.012 (0.3mm)

General rule: Max. clearance =

0.2 x material thickness.

UPPER BLADE

VERTICAL

CLEARANCELOWER BLADE

HORIZONTAL

CLEARANCE = MAXIMUM CLEARANCE

Operating Instructions

GENERAL INFORMATION

Following a few simple tips will reduce wear on the tool and the chance of injury to the user.

With the tool unplugged from the power supply and the ON/OFF Switch in the “OFF” position, become familiar with handling the shear and learning the location of its parts.

Secure or clamp small workpieces to be cut to prevent slippage.

Inspect the blades for excessive wear, rotate or replace if necessary.

Always direct the cord toward the rear, and away from the shear. Keep it away from sharp edges.

Never start the shear with the blades in contact with the material being cut.

Do not exceed recommended capacities for this shear. Premature blade failure will occur when the shear is over-gaged.

To extend blade life and prevent corrosion, frequent lubrication of the blades is recommended. Any light weight machine oil can be used for this purpose.

SLIDE "ON-OFF" SWITCH

The Tool is switched "ON" by the slide switch located at the side of the motor housing.

TO TURN TOOL "ON": slide the switch forward.

TO TURN TOOL "OFF": slide the switch backward.

-8-

1506 specifications

Bosch Power Tools has established itself as a leader in the power tool industry, and the Bosch Power Tools 1506 is a prime example of their commitment to quality, innovation, and user-friendly designs. This versatile tool is ideal for both professionals and DIY enthusiasts, offering a balanced combination of power, precision, and durability.

At the heart of the Bosch 1506 is a robust 6.5-amp motor that delivers a no-load speed of up to 35,000 RPM. This powerful motor ensures that cutting and sanding tasks can be completed quickly and efficiently. It's ideal for a wide range of applications, from woodworking projects to metalworking and beyond. The tool's capabilities are enhanced by an adjustable speed control feature, allowing users to customize the speed based on the material being worked on.

One of the standout features of the Bosch 1506 is its ergonomic design. The tool is crafted with a soft grip handle that reduces fatigue during extended periods of use. This thoughtful design aspect ensures that users maintain optimal control without sacrificing comfort. Additionally, the tool's lightweight construction makes it easy to maneuver in tight spaces, enhancing its overall utility.

The Bosch 1506 is also equipped with advanced dust collection technology. This feature not only keeps your work area clean, but it also prolongs the life of the tool by preventing dust from entering sensitive components. The integrated dust port can easily be connected to a vacuum, allowing for efficient dust extraction.

Another characteristic that sets the Bosch 1506 apart is its versatility. This tool can accommodate a variety of accessories, making it suitable for different tasks, including sanding, grinding, and polishing. This adaptability is complemented by the tool's quick-change chuck system, which allows users to swap accessories swiftly, minimizing downtime.

In terms of safety, Bosch has incorporated several important features into the 1506. The tool comes with a safety switch that prevents accidental startups, as well as a protective guarding system to shield users from debris during operation.

Overall, the Bosch Power Tools 1506 is a powerful, user-friendly tool that showcases the brand's dedication to quality and innovation. With its powerful motor, ergonomic design, advanced dust collection, and versatility, the Bosch 1506 stands out as a reliable option for anyone seeking a dependable power tool for various applications.