Festool 1400 EQ Switching the machine on and off, Electronics, Smooth start-up, Speed regulation

Page 8

8

Switching the machine on and off

Keep the machine steady during switching and during use by holding the handles (3.2, 3.5) with both hands.

Switch (3.4) serves as an On/Off switch. It may be latched with the locking knob on the side (3.3) for continuous operation. Pressing the switch again releases the lock.

After the machine has been switched off, the milling cutter will still rotate for a time. Take care that parts of your body do not come into contact with the milling cutter while it is still rotating!

Electronics

The router OF 1400 EQ has solid shaft electronics with the following functions:

Smooth start-up:

The electronically controlled smooth start-up facility enables start-up of the machine without jerks and requires a lower start-up current.

Speed regulation:

Using the electronic speed control (3.1) the motor speed can be continuously adjusted from 10 000 and 22 500 rpm. The table beside offers a guide to the correct electronic setting for various materials. The settings are naturally infinitely variable.

Constant speed:

The selected motor speed is electronically maintained to a constant level. By this means a uniform cutting speed is achieved.

Do not work with the OF 1400 EQ if the electronic control is defective since this may lead to excessive speeds. A defect in the electronic control is indicated by the absence of a smooth run-up, a higher noise level at idle or the fact that no speed control is possible.

Tool settings

Always disconnect the plug from the power supply before making any adjustments to the router or installing or removing any accessory!

Chips extraction

Chips and dust from routing can be removed by means of a extractor hood. See-through plastic material gives good view of rotating tool. You can connect a Festool extractor with an extractor hose diameter of 36 mm or 27 mm to the extractor connector (4.6). We recommend a diameter of 36 mm because it minimises the risk of blockages.

- Fit the extractor hood to the router base by first inserting the two tenons (4.1) on the extractor hood into the recesses (4.2) on the router base, then place the extractor hood on the router base and close the lever (4.5). To enable fitting and removing the extractor hood with the router attached, the recess (4.3) in the extractor hood can be opened by turning the segment (4.4). For optimised dust extraction, the recess with the rotating segment must be closed during work.

This suction hood can be used only for cutters up to 28 mm diameter.

Chip catcher KSF-OF

Using the KSF-OF chip catcher (4.7) (sometimes included in the scope of delivery), the efficiency of the extraction can be increased when routing edges.

Installation is similar to that of the copying ring (fig. 11).

The hood can be cut off along the grooves (4.8) using a hacksaw and can thus be reduced in size. The chip catcher can then be used for interior radiuses up to a minimum radius of 40 mm.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 1400 EQ General Safety Rules Work area safetyElectrical safety Personal safetyRègles DE Sécurité Générales Normas Generales DE SeguridadConservez CES Instructions Conserve Estas InstruccionesTool use and care ServiceSpecific Safety Rule for Routers Utilisation et entretien des outils Uso y cuidado de la herramientaEntretien et réparation MantenimientoTechnical data SymbolsUse for intended purpose Electrical connectionSymbole Caractéristiques techniquesUtilisation conforme Raccordement électriqueSwitching the machine on and off Tool settingsElectronics Smooth start-upMise en marche et arrêt de la machine Conexión y desconexión de la máquinaElectronique Démarrage en douceurAdjusting the milling depth Setting the zero pointSetting the milling depth Milling cuttersOutils de fraisage Insertion de l’outilRetrait de l’outil Changement de pince de serrageWorking with the router Freehand routingRouting with the parallel guide Routing with the FS guide systemTravailler avec la défonceuse Usinage à la voléeFraiser avec la butée latérale Fraiser avec le système de guidage FSServicing and maintenance Copy cuttingCopying ring Copying deviceMaintenance et entretien Copier un fraisageBague de copiage Fresar copiandoFestool Limited Warranty Accessories, toolsWarranty Conditions of 1+2 Warranty Accessoires, outils Accesorios, herramientasGarantie Conditions de la garantie 1+2 ans Garantie limitée de FestoolPage

1400 EQ specifications

The Festool 1400 EQ is a premium plunge router designed for a wide range of woodworking tasks, blending precision, power, and user-friendly features. This machine stands out among its peers thanks to its advanced engineering and innovative technologies, making it an essential tool for both professionals and woodworking enthusiasts.

One of the primary features of the Festool 1400 EQ is its robust motor, delivering 1400 watts of power. This powerful motor enables the router to handle a variety of materials, including hardwoods, softwoods, and composite materials. The variable speed control allows users to adjust the RPM from 10,000 to 24,000, providing optimal performance for different applications. Whether you are making intricate cuts or performing edge shaping, the speed control ensures precision and efficiency.

The design of the 1400 EQ is user-oriented, featuring an ergonomic handle that provides excellent grip and comfort during operation. The plunge depth can be easily adjusted with a single dial, allowing for precise routing depths without any tools. This feature is particularly beneficial for users who frequently switch between tasks, as it saves time and enhances productivity.

Festool's unique FastFix system further elevates the versatility of the 1400 EQ. This technology enables quick and easy bit changes without the need for additional tools, ensuring that users can swiftly adapt to various routing tasks. The large base and the option to attach a guide rail ensure stability and accuracy, making it easier to achieve clean, smooth cuts.

Another standout characteristic is the integrated dust extraction system. With the ability to connect to a Festool dust extractor, the 1400 EQ effectively minimizes dust and debris in the workspace, creating a cleaner and safer environment. This feature not only enhances visibility during work but also helps in maintaining a healthier atmosphere.

Durability and reliability are core attributes that Festool products are known for, and the 1400 EQ is no exception. Constructed with high-quality materials, this router is designed to withstand the rigors of heavy use, ensuring it remains a reliable tool for years to come.

In summary, the Festool 1400 EQ combines power, precision, and user-friendly features, making it a top choice for anyone serious about woodworking. Its advanced technologies and thoughtful design cater to a range of routing tasks, ensuring that users can achieve their desired results with ease and efficiency.
Top Page Image Contents