Dymo 31-250 instruction manual Attaching and Leveling Feed Table, Attaching Thickness Scale

Page 9

ATTACHING AND LEVELING FEED TABLE

1. Remove the front and rear shipping bolts that were installed to stabilize the support plate during transit. These bolts, one shown at (N) Fig. 5, should be removed before attaching table. Use a ½" wrench to hold hex stop post (S) then with another ½" wrench loosen and remove hex bolts (N)

NOTE: DO NOT remove the hex stop post (S) Fig. 5.

2.The abrasive belt and the motor for the feed table are shipped assembled. Place the feed table (A) Fig. 5 on the support plate (P), inserting the motor side first. Align holes in table (two of which are shown at C) with top of leveling screws (B).

Make sure the table is not sitting on any of the lockwashers attached to leveling screws (B).

3.Fasten the table assembly (A) to the support plate (P) with four 5/16" socket head screws with lock washers through the holes (D), and secure with flange nuts, two of which are shown in (F) Fig. 6D. Tighten securely.

4.With a ½" wrench hold the hex top of the front, right leveling screw (L) Fig .6A. Then using a 3/16" hex wrench loosen screw (B) four full turns. Turn leveling screw clockwise Fig. 6B until it no longer touches the support plate (P) as shown. Then turn it counterclockwise until it just touches the support plate (P) Fig. 6C without raising the plate as shown at (O). Hold the hex top of the leveling screw (L) Fig. 6A and tighten hex screw (B).

D C

A

C

 

 

 

N

B

CAUTION:

B

 

TAG

 

S

P

Fig. 5

B

P

L

Fig. 6A

B

P

L

Fig. 6B

B

O

P

L

Fig. 6C

A

F

P

Fig. 6D

ATTACHING THICKNESS SCALE

1.Remove screw and washer (A) Fig. 7.

2.Place thickness scale (B) Fig. 8 over the hole and replace screw and washer (A).

3.Loosen screw (C) Fig. 9, and position pointer against scale (B) Fig. 9. Tighten screw (C) Fig. 9.

IMPORTANT: Refer to section “CHECKING AND ADJUSTING TABLE HEIGHT” in this manual for adjusting scale.

A

B

Fig. 7

A

B

Fig. 8

B

C

Fig. 9

CONNECTING FEED MOTOR TO FEED/SPEED SWITCH ASSEMBLY

The table feed motor (A) Fig. 10 is located on the side of the feed table (B). Before connecting the feed motor to the feed-speed switch disconnect machine from power source.

1.Insert the feed/speed switch assembly connector

(C) Fig. 10 into the motor connector (D) . Connector is polarized and will fit only one way.

To avoid damage DO NOT connect the motor to any other power source.

A

C

D

B

Fig. 10

9

Image 9
Contents 18 x 36 Drum Sander Important Safety Instructions Safety Guidelines DefinitionsStay ALERT, Watch What YOU are Doing Hold the Work Firmly when sanding Additional Safety Rules For Drum SandersPower Connections Foreword Unpacking and CleaningDrum Sander Parts Carton ContentsAssembly Attaching LegsAttaching the Handwheel Attaching Thickness Scale Attaching and Leveling Feed TableLocking the Drum Switch in the OFF Position Operating Controls and AdjustmentsTable FEED/SPEED Switch Starting and Stopping the MachineDisconnect Machine from Power Source Checking and Adjusting Feed Belt Tracking and TensionRaising and Lowering Feed Table TrackingSetting the Height Scale Checking and Adjusting Table Parallel to DrumChanging Drum SPEEDS/REPLACING Drive Belt Table Height AT this TimeTo relieve tension on the belt. Replace or change the belt Removing and Replacing Drum Sanding BeltDust Collection Removing and Replacing Feed BeltWhen do I Change the Drum SPEED? Frequently Asked QuestionsWhat is Recommended for Dust Collection What Factors Affect Sanding OPERATIONS?What are the Maximum and Minimum Sanding Stock SIZES? What Causes Burn MarksHOW do I Sand Multiple BOARDS? HOW do I Sand the Edges of BOARDS?HOW do I Sand Boards Wider than 18? HOW do I Sand Glued BOARDS?HOW do I GET STARTED? Tips for Increasing Sanding Belt LifeTable Movement Troubleshooting Guide Tension on Timing BeltChecking the Table Support Plate Lock NUT Adjustment Checking Lock NUT AdjustmentBrush Inspection and Replacement MaintenanceDrum Motor Overload Protection Feed Belt Motor Overload ProtectionPage Page PARTS, Service or Warranty Assistance AccessoriesCanadian PORTER-CABLE Delta Service Centers