Schumacher SE-2254 owner manual Operating Instructions Charging Battery in Vehicle

Page 3

F.OPERATING INSTRUCTIONS: CHARGING BATTERY IN VEHICLE

When charging battery in the vehicle, take care to determine the battery type and which post is grounded. To reduce risk of a spark near battery, follow these steps when battery is installed in vehicle. WARNING: A spark near battery may cause battery explosion.

1.Position AC power cord and DC charging cords to reduce risk of damage by hood, door, or moving engine parts.

2.Stay clear of fan blades, belts, pulleys, and other parts that can cause injury.

3.Check polarity of battery posts. Battery case will be marked by each post: POSITIVE (POS, P, +) and NEGATIVE (NEG, N, -). NOTE: The positive battery post usually has a larger diameter than the negative post.

4.Determine which post of battery is ground (connected) to chassis.

NOTE: The negative post is normally grounded.

NEGATIVE GROUNDED POST

5A. For negative-grounded vehicle, connect POSITIVE (RED) clip from battery charger to POSITIVE (POS, P, +) un- grounded post of battery. Connect NEGATIVE (BLACK) clip to vehicle chassis or engine block away from battery. Con- nect to a heavy gauge metal part of the frame or engine block.

POSITIVE GROUNDED POST

5B. For positive-grounded vehicle, connect NEGATIVE (BLACK) clip from battery charger to NEGATIVE (NEG, N, -) un- grounded post of battery. Connect POSITIVE (RED) clip to vehicle chassis or engine block away from battery. Con- nect to a heavy gauge unpainted metal part of the frame or engine block.

WARNING: Do not connect clip to carburetor, fuel lines, or

sheet-metal body parts. NOTE: Attach clips to battery post and twist or rock back and forth several times to make a good connection. This tends to keep clips from slipping off terminals and helps to reduce risk of sparking

6.Follow steps 1-4 in Battery Charger Section K.

7.When the battery is fully charged, unplug the charger from the AC power source.

8.Remove charger clips from (1) chassis and (2) battery pole in that order.

9.Clean and store battery charger.

G.OPERATING INSTRUCTIONS: CHARGING BATTERY OUT OF VEHICLE

When charging battery out of vehicle, take care to determine the battery type. To reduce risk of a spark near battery, follow these steps when battery is outside vehicle. WARNING: A spark near the battery may cause battery explosion. WARNING: When removing battery from vehicle or boat, disconnect grounded pole first. When disconnecting, make sure all accessories are off, so as not to cause an arc. (NOTE: A marine (boat) battery must be removed and charged on shore. (To charge on board requires special equipment designed for marine use.) WARNING: When reinstalling battery, attach the ground post first.

1.Check polarity of battery posts. Battery case will be marked by each post: POSITIVE (POS, P, +) and NEGATIVE (NEG, N, -). NOTE: The positive battery post usually has a larger diameter than the negative post.

2.Attach a 24-inch long (or longer) 6-gauge (AWG) insulated battery cable to NEGATIVE (NEG, N, -) battery post. (The 24" lead is not supplied. You may purchase at most automotive stores.)

The 24" lead provides a safer connection condition. Spark- ing or arcing could occur when connecting the charger clip to the lead.

3.Connect POSITIVE (RED) charger clip to POSITIVE (POS, P, +) post of battery. Rock clip back and forth to make good connection.

4.Position yourself and free end of 24 inch cable as far away from battery as possible. Then connect NEGATIVE (BLACK) charger clip to free end of cable.

WARNING: Do not face battery when making final con- nection. Rock clip back and forth to make a good connec- tion.

5.Follow steps 1-4 in Battery Charger Section.

6.When battery is fully charged, unplug charger from AC outlet.

24" Cable

Battery Cable

7.When battery is fully charged and the charger is unplugged:

(1)Remove clip from end of the Negative end of cable, then

(2)Remove clip from Positive battery post, in that order.

8.Clean and store battery charger.

WARNING: Be sure area around the battery is well ventilated while battery is being charged. Gas can be forcefully blown away by using a piece of cardboard or other non-metallic material as a fan.

3

Image 3
Contents Business Center Drive Mount PROSPECT, Illinois General Battery SafetyPreparing to Charge Personal Precautions and SafetyGround and AC Power Cord Connections Charger Location PrecautionsOperating Instructions Charging Battery OUT of Vehicle Operating Instructions Charging Battery in VehicleOutput Selector Controls Volt BatteryCharge Period Battery ChargingBattery SIZE/RATING Charge RATE*/CHARGING Time Hours Engine StartProblema Causa Posible Solucion Assembly InstructionsTroubleshooting Problem Possible Cause SolutionSeguridad General DE Acumuladores Precauciones Personales Y DE SeguridadPreparacion Para Cargar Garantia Terminal Negativo a TierraTerminal Positivo a Tierra Tiempo DE Carga