Maintenance, Five Year Tool Limited Warranty

HOLD Function

Data Hold Function - Freezes the value on the display. Press the “HOLD” button to freeze the reading. The reading will be held regardless of subsequent variation in input. HOLD is displayed with the reading. To exit Data Hold mode, press the HOLD button again. Hold is not available when using the Inrush Function.

MIN/MAX Function

CAUTION Make a measurement and press the MIN/MAX button after an appropriate range is selected by the auto- ranging function.

The MIN/MAX recording mode cap- tures the minimum and maximum input values.

Set the dial to to the desired measure-
ment function. Make a measurement	Press
and press the MIN/MAX button. The
meter will capture the MIN and MAX
readings. Press the MIN/MAX button
to toggle between the captured MIN,
MAX and present readings. MAXMIN
ﬂashes when the present reading is
displayed.

To exit and erase stored readings, press the MIN/MAX button for two seconds or change the dial.

If MIN/MAX is active, all function but- tons are unavailable except HOLD.

DANGER To avoid electrical shock: Never make measurement on a circuit in which voltage over 1000V exists.

Inrush Function (Cat. No. 2239-20 only) Inrush current measurement allows for measuring the sharp peak in current upon motor startups. Lasting only part of a second, MILWAUKEE's Inrush function captures and displays the ﬁrst 100 millisec- onds of current at motor startup.

1.Power off the system under test.

2.Press the jaw opening trigger
to open the jaws and clamp	EDE
	V
	O
	L
	TA
them onto the conductor	G
them onto the conductor	ET
	TC
	RO
under test.

NOTE: Do not clamp
over 2 or more wires	0FF	0FF
at the same time.	0FF	0FF
at the same time.
Irregular results
will occur.

3.Set the Rotary
Dial to or	GA
	V
	O
	L
position. AC or DC	T
position. AC or DC	TCE
	E
	D
	TE
mark is displayed.	RO
mark is displayed.

4.Press the INRUSH
button.	0N	0N
5.Power on the
system under test.
6.The reading is
displayed.

Over-ﬂow indication

MAINTENANCE

WARNING To reduce the risk of injury, always unplug the charger and remove the battery pack from the charger or tool before performing any maintenance. Never disas- semble the tool, battery pack or charger. Contact a MILWAUKEE service facility for ALL repairs.

Maintaining Tool

Keep your tool, battery pack and charger in good repair by adopting a regular maintenance program. After six months to one year, depending on use, return the tool, battery pack and charger to a MILWAUKEE service facility service.

If the tool does not start or operate at full power with a fully charged battery pack, clean the contacts on the battery pack. If the tool still does not work properly, return the tool, charger and battery pack, to a MILWAUKEE service facility for repairs.

WARNING To reduce the risk of per- sonal injury and damage, never immerse your tool, battery pack or charger in liquid or allow a liquid to ﬂow inside them.

Cleaning

Clean dust and debris from charger and tool vents. Keep tool handles clean, dry and free of oil or grease. Use only mild soap and a damp cloth to clean the tool, battery pack and charger since certain cleaning agents and solvents are harmful to plastics and other

FIVE YEAR TOOL

LIMITED WARRANTY

MILWAUKEE Test & Measurement Products (includ- ing bare tool, li-ion battery pack(s) and battery char- ger but excluding alkaline batteries) are warranted to the original purchaser only to be free from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will repair or replace any part on this product which, after examination, is deter- mined by MILWAUKEE to be defective in material or workmanship for a period of ﬁve (5) years* after the date of purchase. Return the Test & Measurement tool and a copy of proof of purchase to the nearest Milwaukee Electric Tool Corporation - factory Service Center. This warranty does not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE autho- rized personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.

*The warranty period for the LITHIUM-ION battery pack that ships with the Test & Measurement tool is two (2) years from the date of purchase. *Alkaline battery that ships with Test & Measurement tool is separately warranted by the battery manufacturer. *The warranty period for a NON-CONTACT VOLT- AGE DETECTOR – 2201 20 is one (1) year from the date of purchase.

Warranty Registration is not necessary to obtain the applicable warranty on MILWAUKEE product. The manufacturing date of the product will be used to determine the warranty period if no proof of purchase is provided at the time warranty service is requested.

ZERO Function
(Cat. No. 2239-20 only)	Press

AC Current / DC Current : When the LCD doesn’t read ZERO while the Jaws are closed, press the ZERO Button to in- dicate ZERO before starting a measurement. With the jaws closed and without clamping them around a conductor, press the ZERO key to zero adjust the display.

The “ZERO” mark appears on the LCD to indicate the ZERO Function is activated.

°F / °C (Cat. No. 2238-20 only)

To switch between Fahrenheit or Celsius, press the °F / °C button.

Any time the input exceeds the measuring range “OL” or “-OL” is displayed.

Worklight LED ON/OFF

To turn the light on and off, pull the trigger.

Sleep Mode

CAUTION The Data Hold readings are released when the meter enters Sleep Mode.

The clamp meter is automatically powered off in about 20 min after the last Rotary Dial or button operation. To reset, rotate the Rotary Dial or pull the trigger. If the display is still blank when a new Rotary Dial setting is selected, charge the battery pack.

To disable the sleep function, turn the tool off. Press and hold the HOLD button and turn on the meter. After the meter "beeps", release the HOLD button. The meter will beep again and the clock symbol will be removed from the display.

The clamp meter does use battery power in sleep mode. Be sure to switch the tool to OFF to conserve battery power.

insulated parts. Some of these include gasoline, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia and household deter- gents containing ammonia. Never use ﬂammable or combustible solvents around tools.

Repairs

For repairs, return the tool, battery pack and char- ger to the nearest service center listed on the back cover of this operator's manual.

ACCESSORIES

WARNING Always remove battery pack before changing or removing acces- sories. Only use accessories specifically recommended for this tool. Others may be hazardous.

For a complete listing of accessories refer to your MILWAUKEE Electric Tool catalog or go online to www.milwaukeetool.com. To obtain a catalog, con- tact your local distributor or a service center listed on the back cover of this operator’s manual.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CON- SEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES OR CON- DITIONS, WRITTEN OR ORAL, EXPRESSED OR IMPLIED. WITHOUT LIMITING THE GENERALITY OF THE FOREGOING, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABIL- ITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE, AND ALL OTHER WARRANTIES.

This warranty applies to product sold in the U.S.A.,

9 Canada and Mexico only.