Chicago Electric 97594 operating instructions Gfci reduces the risk of electric shock

Page 3

plugs with grounded power tools. Unmodified plugs and matching out- lets will reduce risk of electric shock.

b.Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

d.Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

e.When operating a power tool out- doors, use an extension cord suit- able for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is unavoidable, use a Ground Fault Circuit Interrupter (GFCI) protected supply. Use of

a GFCI reduces the risk of electric shock.

3.Personal safety

a.Stay alert, watch what you are do- ing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

b.Use personal protective equip- ment. Always wear eye protection.

Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropri- ate conditions will reduce personal injuries.

c. Prevent unintentional starting.

Ensure the switch is in the off-po- sition before connecting to power source and/or battery pack, pick- ing up or carrying the tool. Carry- ing power tools with your finger on the switch or energizing power tools that have the switch on invites acci- dents.

d.Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left at- tached to a rotating part of the power tool may result in personal injury.

e.Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

g.If devices are provided for the con- nection of dust extraction and col- lection facilities, ensure these are connected and properly used. Use of these devices can reduce dust- related hazards.

h.Only use safety equipment that has been approved by an appropri- ate standards agency. Unapproved safety equipment may not provide adequate protection. Eye protection must be ANSI-approved and breath- ing protection must be NIOSH-ap-

SKU 97594

For technical questions, please call 1-800-444-3353.

Page 3

Image 3
Contents Magnesium Heavy Duty Low Speed 1/2 Drill Save This Manual General Power Tool SafetyGfci reduces the risk of electric shock Drill and Impact Drill Safety Warnings Vibration Safety Grounded Tools Tools with Three Prong Plugs GroundingExtension Cords Double Insulated Tools Tools With Two Prong PlugsTable a Extension Cord Length SymbologyInstructions for putting into use SpecificationsFunctionsTool Set Up UnpackingWork Piece and Work Area Set Up General Operating InstructionsDrilling Operation Wood Drilling Metal DrillingCleaning, Maintenance, Lubrication Maintenance ServicingProblem Possible Causes Possible Solutions TroubleshootingQTY Parts ListAssembly Diagram Limited 90 DAY Warranty Perceuse À Haut Rendement Avertissements sur la sécurité Des outils électriques Gardez CE GuideÉlectrique augmente les risques de décharge électrique Priées réduira les risques de blessu- res personnelles Contrôler Vibrations Sécurité Mise À LA Terre Sauvegardez CES InstructionsFiche à Deux Broches LES Outils À Double Isolation LES Outils AvecCalibre Minimum DES Rallonges SymbolesInstructions Pour Utilisation SpécificationsDéballage Instructions ’UTILISATIONInstructions Générales ’Utilisation Endroit DE Travail ET AirePerçage Percer le métalPercer le bois Modèle Nettoyage, Entretien et Lubrification EntretienDépannage Problème Causes possibles Solutions possiblesQTÉ Liste DE PiècesDiagramme D’ASSEMBLAGE Garantie Limitée DE 90 Jours