HP SCP Software for s manual Original Size, Print Size

Page 55

Original Size

The size of the original (width and height) is shown under O RIGI NAL SI ZE .

Print Size

The Print Size can be different from the original size.

By default, the original size entered is taken as the output size. The output size can be increased or reduced by a percentage. You may of course enter the desired copy size directly in millimeter or inch. The copy width or length always changes proportionally when you alter one of these parameters.

The SET SI ZE button opens a menu, where you can pick a predefined size or decide to print with MAXI MUM PRI NT SI ZE depending on the size of the medium in use.

Hint: With the key combination Ctrl and Page-up, the maximum print width will be displayed.

Copies

Enter the number of copies required under CO PI ES . If a test copy is supposed to be done first, set the number of copies to "1".

The option JO B COUNT given below the tab area is not to be confused with the number of CO P I ES , since JOB COUNT defines the number of repetitions of the same job, whilst CO PI E S sets the number of the selected document. Just pay attention to the information under the NO . column in the job list after altering the J O B COUNT or COP IE S parameters.

Printer

Select the desired output device from the drop down list which contains all installed printers, printer clusters and queues. You are able to select different output devices within one print job process.

Note that access to some picture- and output arrangement options may depend on the selected queue or cluster in this list, since an administrator can reduce functions for clients who work with these devices. Go to

§CREATE QUEUE TAB QUEUE or § CREATE PRINTER CLUSTER TAB QUEUE to learn the details.

If a printer is not working correctly and/or its installation is corrupted, the name of the device will appear with red letters. A pop up box will inform you about the error when pointing to the printer name.

The button next to the printer list opens the window for the printer/queue configuration. The dialog for the printer configuration is device-dependent:

In the tab PRI NT OP TI O NS you can change the settings of your printer. In the tab PL ACEMENT you set additional arrangements of the picture.

For further details regarding to this subjects, see § THE CONFIGURATION WIZARD § PLACEMENT and §

DEFAULT SETTINGS OF THE PRINT OPTIONS.

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents SCP reprocontrol for HP Manual Content Create USER-DEFINED Formats REPROCONTROL.CLIENT Main Applications Setting the Black and White Points with the Pickers Emove Done JOB Records After Operating Systems Introduction / RequirementsSystem Requirements Hardware RequirementsPrinter installation InstallationInstallation of the Hardlock Installation of the Program Reprocontrol.server Page Login Keycode Entry Printer Configuration Hardware ConfigurationPrinters / Queues Delete Printer Single Configuration DialogsWindows Spooling Configuration WizardName / Connection Printer NamePlacement Alignment RotateRollwidth tolerance Technical Label Define Medialist Configuration / Loaded ConsumablesDefault Settings for Print Options Page Calibration for RIP CalibrationCalibration Target Print Target Profile Library Get ProfilesExport to Library On-site Calibration SpectrophotometerEdit media parameters Reset media parametersDelete Calibration Edit size correctionTarget Selection Printer Create QueueTab General QueueSet Print Size Use Printer Default SettingsPicture Edit Settings MediumCopies Tab Output OptionsSet Output Size De-/Activation of the Queue Tab QueueQueue description PriorityListen to LPR Set User Rights to change QueueListen to raw port Tab Hpgl Cost optimizing Create Printer ClusterLoad Sharing Simulation of a multiroll printerPage Max. Print size Distribute jobs among similar printers of the cluster Wait for best fitting Printer when busyAllow monochrome prints on color printers Create user-defined formats PreferencesTab General Paper FormatUnit Simple filter editor by Default for RIPShow warning when configuration changes Show warning when unsaved changes will be deletedUse compressed transfer Exit Menu Bar OptionsFile Files to Print SelectionPrinters/Queues ConfigurationPreferences Apply Settings Globally Load presetSave preset Set as defaultChange password Show preflight ViewPreview Show button captionActivate all Switch activeEdit DownInfo ActionsHelp Basics Reprocontrol.client main applicationsFeatures of the Toolbar Reload Job Start new jobPreview Edit AOI Reset AOI Setting Apply FilteringRIP Preview Select an AreaSoftproof Show Gamut WarningFile Edit Images and OutputUse Color Management Print Size Original SizeFilter Print ModeBrightness Pen Settings Change Pen Color User Pen SettingsSave / Load Pen Parameters Functions and Structure of the Filter Editor Filter EditorPreview of the Filter Editor Histogram Black Point Adaptive Setting the Black and White Points with the PickersText/Background StaticWhite Point Adaptive ContrastDespeckling Tab Postprocessing Black & White ModeTo use this filter Inverted Hole FillingGamma Gamma sliders Tab Gamma Correction Color Mode without Color ManagementGray Balance Sliders for the White Point Tab Enhancement Color Mode with Color ManagementLevel Tab Special Filter All Modes except of Black & White ModeNone Adaptive SharpnessLimit Hint Using the adaptive sharpness filterDisplay Transfer Function Sharp SmoothFilter Radius µm Tab Color Adjust Color Mode with Color Management Tab Color Exchange Color Mode with Color Management Lab Color Space Reprocontrol.WinDriver Tab Log WinDriver SettingsTab Settings Use last settingsUsing the WinDriver Tab Jobs Reprocontrol.monitorButton commands Tab Connection Tab Printers/QueuesMenu Options Keycode Tab ConfigurationJob Database Unit Summary CosttrackerDetails Page Export PreferencesCalibration of the costtracker Reprocontrol.backup
Top Page Image Contents