HP Z800 manual Single XR 6412 RAID enclosure, 4 loops

Page 39

Single XR 6412 RAID enclosure, 4 loops

To FC adapter on workstation / LMS (port 0)

To FC adapter (port 3)

To FC adapter (port 1)

To FC adapter (port 2)

XR RAID Enclosure

0

FACTORY

 

USE ONLY

0

FACTORY

 

USE ONLY

XE (EBOD) Expansion Enclosure

0

1

0

 

 

 

ID

0

1

0

 

 

 

ID

XE (EBOD) Expansion Enclosure

0

1

0

 

 

ID

0

1

0

 

 

 

ID

XE (EBOD) Expansion Enclosure

0

1

0

 

 

 

ID

0

1

0

 

 

 

ID

XE (EBOD) Expansion Enclosure

0

1

0

 

 

ID

0

1

0

 

 

 

ID

Cabling for additional enclosures

NOTE In a 4-loop configuration with a XR 6412 RAID enclosure, you need a minimum of one XE expansion enclosure attached to the XR RAID enclosure.

Connecting Storage Enclosures 35

Image 39
Contents HP Z800 Workstation Hardware Setup Guide Trademarks Contents Setting Up Video Hardware Iv ContentsIntroduction About This GuideRelated Documentation Convention Example Notation ConventionsContacting Customer Support IntroductionGeneral Workflow Getting StartedGetting Started Workstation Control Surface Lustre Master Workstation Typical Configuration Overview for Autodesk LustreMemory Requirements Hardware Configuration GuidelinesPower and Air Conditioning Requirements Hardware Configuration GuidelinesUnit Conversion Example Rack Mount RequirementsComponent Quantity Startup Amps Cont. Amps Watts 120V 240VAvoiding Damage from Static Electricity Avoiding Damage from Static ElectricityGrounding Audio Hardware Components Receiving Your ShipmentPage Workflow for Connecting Peripherals Connecting PeripheralsTo connect the monitor Connecting the Graphics MonitorConnecting Peripherals Connections OverviewConnecting the Keyboard, Mouse, and Tablet Connecting the Graphics Monitor Calibration DeviceConnecting the Keyboard, Mouse, and Tablet Connect the built-in GigE port as follows To enable the Eye-One calibration utility driverNetwork Connections Visual Effects and Finishing WorkstationConnect the GigE adapter as follows Connecting the Autodesk Control SurfaceLustre Workstation Lustre WorkstationConnecting the Slave Renderer to a Lustre Workstation HP Z800 WorkstationTo connect the Autodesk Control Surface To connect the Slave Renderer Connecting the Slave Renderer to a Lustre WorkstationPage Setting UpVideo Hardware4 Video Hardware ComponentsIncluded Components Setting Up Video Hardware Wiring Your Video ComponentsSetting Up VTR Emulation Setting Up VTR EmulationTo configure hardware for VTR emulation About Audio SettingUpAudioHardware5Audio Wiring Workflow To wire the audio subsystemAudio Wiring Setting Up Audio HardwareAudio Hardware Components Configuring the Lucid ADA 88192 Converter Configuring the Lucid ADA 88192 ConverterDo this Adjusting Lucid ADA 88192 Converter SettingsTo navigate menus and adjust settings To reset all settings to their factory defaultsMenu Menu Item Comment Lucid ADA 88192 Converter Settings for Remote ControlLucid ADA 88192 Converter Settings for Local Control Lucid ADA 88192 Converter Settings for Remote ControlAJA Keyword SettingConnecting Storage Connecting Media StorageOverview Connecting the HP Z800 Atto Fibre Channel Adapter Connecting StorageStorage Configuration Loops Expected Peformance Connecting the HP Z800 Atto Fibre Channel Adapter XR 6500 Wiring Diagrams Connecting Storage EnclosuresSingle XR 6500 RAID enclosure, 4 loops Connecting Storage EnclosuresSingle XR 6412 RAID enclosure, 2 loops XR 6412 Wiring DiagramsSingle XR 6412 RAID enclosure, 4 loops XR 5402 and XR 5412 Wiring Diagrams Scsi Tape Drive Devices Connecting Archiving StorageConnecting Archiving Storage Filesystem DevicesConnecting Storage Scsi Tape Drive Devices Page Configuring Workstation Bios HP Z800 Bios SettingsBios Menu Submenu Value Restoring Bios to Default Factory Settings Configuring the Workstation BiosTo restore default factory Bios settings Updating your System Bios Updating your System BiosTo update the Bios on your workstation Workstation reboots Standard VTR Control Cable Pinouts VTR Control Cable PinoutsVTR Emulation RS-422 Control Cables LinuxAJAAppendix a VTR Control Cable Pinouts Linux Master to Linux Emulator LinuxAJA Master LinuxAJA EmulatorLinux Master to Linux Emulator VTR-Emulation Control Cable Third-Party Master to Linux EmulatorIndex IndexRAID