Sterling 350-2100 CFM installation manual Desiccant Replacement Procedure, First AID

Page 39

•Noticeable amounts of desiccant in the beds is a medium-brown color, or darker.

If any of these signs are noticed, the desiccant in the desiccant beds should be replaced. Desiccant replacement kits are available from the Parts Department. If you wish, the desiccant beds can be repacked at your site by a technician.

WARNING

DESICCANT MATERIAL CAUSES EYE IRRITATION

BREATHING MAY BE HARMFUL/MAY CAUSE SKIN IRRITATION

;Do not get in eyes.

;Avoid prolonged contact with skin.

;Use with adequate ventilation.

;Wash thoroughly after handling.

FIRST AID:

In case of eye contact, immediately flush eyes with plenty of water for at least 15 minutes. If irritation persists, see a physician.

6-8 Desiccant Replacement Procedure

Follow the procedure below to change the desiccant.

1.Disconnect electrical power to the dryer.

2.Remove the bolts and nuts securing the cover of each desiccant tower. Remove the covers with a lifting fixture.

3.With a shop vacuum, carefully remove all desiccant from each tower.

4.Inspect each lower desiccant screen for tears or burn-through spots. Replace if necessary.

5.After cleaning each tower, add a level layer of half the large bead desiccant on top of the screen. Next, carefully add the full amount specified "per bed" of small bead desiccant. Smooth the top level, and finally add another layer of the remaining large bead desiccant to the top. Make sure this layer is level and smooth.

6.Repeat the above step for the other bed.

7.Inspect the gasketing on each of the covers. Replace if necessary.

8.Re-install the covers.

350-2100 cfm Dryers

Chapter 6: Maintenance

39 of 58

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Large Dehumidifying Dryers SDA Series 350 2100 CFMWrite Down Your Serial Numbers Here For Future Reference Shipping Info Table of Contents Maintenance Safety How to Use This ManualSafety Symbols Used in this Manual Dryer Safety Tags Safety Tag InformationWear Safety Glasses and Work Gloves Responsibility General ResponsibilityOperator Responsibility Remember Maintenance ResponsibilityReporting a Safety Defect Models Covered in This Manual Typical Features and ComponentsOptional Features Functional DescriptionWhat is Desiccant? Closed Loop Drying SystemProcess/Regeneration Cycle Cfm Dryers Functional Description TOP View Left Side View Check For Proper Blower Rotation InstallationWork Rules Electrical ConnectionsDrying Hopper Air Trap Aftercooler Cooling Water ConnectionTypical Control Panel Control Panel Control Panel Indicator LightsProcess Blower Failure Alarm Valve Position Error Switches and MetersPLC Control Process Air Temperature ControllerProcess Air Temperature Controller Process Value Numeric LED Temperature Controller LED IndicatorsOptional Communications Protocols Temperature Controller Keys See in SectionStartup, Shutdown & Operation Pre-Startup ChecksStartup Shutdown Setting the Process Air TemperatureSetting the High and Low Temperature Alarms To Change the Process Air High Temperature Alarm SettingEnabling the Lockout Feature Temperature Controller Autotune ProcedureTemperature Controller Internal Switches Temperature Controller Anti-Tamper Lockout SwitchSetting the Dewpoint Extend Shift Point Changing the Display from Fahrenheit to CentigradeTo Change the Dewpoint Shift Point HH Setpoint Heater Cut Off Temp 300F Regeneration Monitoring System Signal ProcessorLL Setpoint Low Regeneration Alarm Setpoint 130F Setpoint Regeneration Blower Shutdown Temp 160FSeven Day Timer Optional Auxiliary Process Safety System OptionalSetting the start up time Setting the Current Day of the Week, Hour and MinuteSetting the stop time Put the timer into Run modeSet the days of the week for automatic operation Maintenance Filter Cleaning/ReplacementServicing the Process Air Filters Models Servicing the Process Air Filters Models 850 through Filter Cleaning/ReplacementDirty Filter Alarm Calibration To Clean the Regeneration FilterServicing the Regeneration Filter Dewpoint Control System Service Symptoms of Worn Out DesiccantTo check the dewpoint sensor and dewpoint control board First AID Desiccant Replacement ProcedureDesiccant Amounts Required Process Heater Replacement ProcedureSpots and lead to premature heater failure Regeneration Heater Replacement ProcedureRestoring a Temperature Controller to the Factory Setup Switch To select a setting 10F Process Temperature Control Error Messages Regeneration Monitor Signal Processor Error Messages Moving Between Levels Regeneration Monitor Advanced ProgrammingSetpoints HysteresisInput Shift Security Protection Sensor Input Type Scale IndicationDisplay Refresh Cycle Problem Possible Cause Corrective Action TroubleshootingProblem Possible Cause Corrective Action Problem Possible Cause Corrective Action Credit Returns Warranty ReturnsAppendix Returned Material PolicyCfm Dryers Appendix Preventive Maintenance Checklist Dehumidifying Dryers Sales Department Service DepartmentTechnical Assistance Parts Department

350-2100 CFM specifications

The Sterling 350-2100 CFM is a high-performance ventilation system that effectively addresses the needs of various industrial and commercial applications. This versatile unit is designed to provide optimal air movement, offering flow rates spanning from 350 to 2100 cubic feet per minute (CFM). Its capabilities make it ideal for environments that require robust air circulation, such as warehouses, factories, and workshops.

One of the standout features of the Sterling 350-2100 CFM is its energy-efficient motor. The unit is equipped with a reliable and durable drive system, allowing for lower energy consumption while maintaining high performance. This not only reduces operational costs but also contributes to a greener footprint, making it an attractive option for businesses looking to enhance sustainability.

The ventilation system is designed with an advanced aerodynamic blade technology that maximizes airflow and minimizes noise levels. This allows for a more comfortable working environment by reducing the disruption typically associated with high-velocity air movement. Additionally, the integrated sound-dampening features ensure that it operates quietly, making it suitable for noise-sensitive areas.

The Sterling 350-2100 CFM also incorporates a user-friendly control panel, which allows for easy adjustments and monitoring of airflow levels. This system can be tailored to specific ventilation requirements, ensuring optimal performance in diverse settings. For added convenience, some models come with remote control capabilities, allowing operators to manage airflow from a distance.

Durability is a key characteristic of the Sterling 350-2100 CFM. The unit is constructed with high-grade materials that resist wear and tear, providing long-lasting service even in challenging environments. The weather-resistant design further enhances its suitability for outdoor applications.

Moreover, the system can be easily integrated with existing HVAC setups, providing flexibility and compatibility without extensive modifications. Maintenance is also simplified, with easily accessible components for routine checks and servicing.

In summary, the Sterling 350-2100 CFM ventilation system stands out for its combination of energy efficiency, quiet operation, and robust design. With its innovative technologies and user-friendly features, it meets the demands of modern industrial and commercial spaces while ensuring optimal air quality and comfort for occupants.
Top Page Image Contents