Sterling SDF 500, SDF 400, SDF 250 manual Assembly, Storage

Page 59

SDF 250/400/500

7.2. Assembly

Please ensure adequate carrying capacity of the lifting equipment.

Check the carrying capacity of the point of installation, particularly if installed on a platform.

The place selected for installation should be as free of vibrations as possible.

The main switch must be freely accessible.

Ground the equipment against electrostatic charging.

FThe machine must not be tilted or laid on its side.

Because of its compact construction the dryer can be installed directly beside the processing machine (drying hopper on the processing machine) or with one or more drying hoppers as a movable facility (compact facility).

Special foundations are not necessary for installation.

The dryer must be installed on a level surface and must not be exposed to excessive humidity. The maximum permissible ambient temperature is 45 °C (113°F).

To facilitate servicing, the dryer should be installed in such a way that that it is accessible from 3 sides. Make sure that the air filters can be changed without problems.

To conserve energy, keep the distance between dryer, hopper and processing machine as small as possible.

The wheels of the compact unit should be locked to ensure stable installation.

The foil should be removed from the drying hopper.

7.3. Storage

The control system may only be stored at temperatures from 0 to +55°C (32 to +131 °F). Between delivery and machine commissioning the equipment should be stored in a dry, dust-free and vibration-free room.

Transport, Assembly and Storage 7-4

Image 59

Contents Sterling Material Processing SDF 250/400/500 SDF 250/400/500 Table of contents 10-1 General Information SDF 250/400/500 SDF 250/400/500 Fields of applications Explanations and informationLegal basis Safety instructions General Operation AssemblyMaintenance For the safety of the devices Start up Touch Screen Control UnitSwitching on the Dryer Entering Dryer Values Basic parametersDew point Act Heater Reg. ActExit air Act Dew point maxEntering hopper values Drying time Target Hopper temp TargetHopper temp Act Granule TempSetting the timer Timer is only operating, when the dryer is switched on Actual operation status Actual hopper temperature displayed in C Status dryerObserving processing status Setting date and time Changing language SDF 250/400/500 Continuous operation SDF 250/400/500 Start up Switching the dryer/hopper heater off Error and error correction LED Alarm Actual messages Excess Temperature Return Air Error Bypass FlapError Valve Block Temperature Measurement Outgoing Air DefectiveExcess Temperature Granules Hopper Excess Temperature Heater HopperInsufficient Temperature Heater Hopper Temperature Measurement Granules Defective HopperOverload Drying Heater STB has been activated Main switch hopper heater # Controller is offOverload Regeneration Heater STB has been activated Alarm protocol Maintenance SDF 250/400/500 Maintenance schedule Cleaning or Replacing the Air Filter SDF Dryer Cleaning or Replacing the Return Air FilterCleaning or Replacing the Regeneration air filter Filter of the electrical cabinet Disposing of Drying Agents Cleaning the Drying Hopper STT Remove any granules remaining in the cleaning openingSTT 60 Notch on the battery connector must point to the left Changing the battery of the control systemSDF 250/400/500 Resetting the control values Functional description General Information Dew point dependent regeneration switch optionalHopper heaters optional Drying Hopper OptionalReturn Air Cooler Optional Connection to a Pneumatic Conveying System OptionalTransport, Assembly and Storage Transport with a fork lift truck Tansport and PackingTransport with a workshop crane Storage AssemblyAssembly instructions Connection of Return Air Cooler Optional Electrical Connection Compressed Air Supply Performance Technical dataBasic Version Optional EquipmentSDF 250/400/500 Accessories Accessories Spare parts list Drying Hoppers STT 25 STT STT 25 STT STT 25 STT STT 25 STT STT 25 STT STT 25 STT