Sterling 882.00291.00 specifications Maintenance Responsibility, Reporting a Safety Defect

Page 9

•Shut off power to the dryer when it is not in use. Turn the switch to the OFF position, or unplug it from the power source.

Maintenance Responsibility

Proper maintenance is essential to safety. If you are a maintenance worker, you must make safety a priority to effectively repair and maintain equipment.

Before removing, adjusting, or replacing parts on a machine, remember to turn off all electric supplies and all accessory equipment at the machine, and disconnect and lockout electrical power. Attach warning tags to the disconnect switch.

When you need to perform maintenance or repair work on a dryer above floor level, use a solid platform or a hydraulic elevator. If there is a permanently installed catwalk on your equipment, use it. The work platform should have secure footing and a place for tools and parts. DO NOT climb on dryers, machines, or work from ladders.

If you need to repair a large component, use appropriate handling equipment. Before you use handling equipment (portable “A” frames, electric boom trucks, fork trucks, overhead cranes) be sure the load does not exceed the capacity of the handling equipment or cause it to become unstable.

Carefully test the condition of lifting cables, chains, ropes, slings, and hooks before using them to lift a load.

Be sure that all non-current carrying parts are correctly connected to earth ground with an electrical conductor that complies with current codes. Install in accordance with national and local codes.

When you have completed the repair or maintenance procedure, check your work and remove your tools, rigging, and handling equipment.

Do not restore power to the dryer until all persons are clear of the area. DO NOT start and run the dryer until you are sure all parts are functioning correctly.

BEFORE you turn the dryer over to the operator for production, verify all dryer enclosure panels, guards and safety devices are in place and functioning properly.

Reporting a Safety Defect

If you believe that your equipment has a defect that could cause injury, you should immediately discontinue its use and inform the manufacturer.

The principle factors that can result in injury are failure to follow proper operating procedures (i.e. lockout/tag out), or failure to maintain a clean and safe working environment.

15, 30, & 60 cfm Compact Dryers

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 15, 30, & 60 cfm Compact Dehumidifying Dryers Unpacking and Inspection Shipping InformationEvent of Shipping Damage If the Shipment is Not CompleteTable of Contents Maintenance Safety How to Use This ManualSafety Symbols Used in this Manual Wear Safety Glasses and Work Gloves Safety Tag InformationResponsibility General ResponsibilityOperator Responsibility Remember Reporting a Safety Defect Maintenance ResponsibilityFunctional Description Models Covered in This ManualGeneral Description Standard Features Mechanical FeaturesElectrical Features Safety Devices and Interlocks Controller FeaturesOptions Safety Circuit Standards Safety Device Lock-OutsFail Safe Operation Installation Uncrating the EquipmentRigging and Placing the Dryer Suggested Lift Rigging for Cart Mount Dryers Suggested Lift Rigging for Machine Mounted Dryers Electrical ConnectionsChecking for Proper Blower Rotation Three-Phase Models Setup ProceduresInitial Start-up Installing Water LinesDrying Hopper Air Trap Considerations Optional AftercoolerShutting Down the Dryer Auto-Tuning the DryerIndicator Lights SwitchesOperation Controller Description and OperationProcess Air Temperature Controller Lit when Control Output 2 is on. Not used Lit when Control Output 1 is on. The Out1Indicator Name Description Lights in the Operation Indicator Section whenSetting the Process Air Temperature Adjustment Level Indicator Name DescriptionE5CN Operating Parameters Entering Operating Parameters to Select Modes Setting the High Dew Point Alarm Process Air Dew Point DisplayOptional Controller Operation Dryer Operation ProceduresAlarm Display Messages High Temp Valve MTR Preventative Maintenance Schedule MaintenanceRecommendations for Cleaning and Replacing Filters Preventative MaintenanceServicing Process Air Filters VacuumingCleaning with Compressed Air Corrective MaintenanceSymptoms of Worn Desiccant Servicing the Dew Point MonitorReplacing Worn Desiccant + First AID +Desiccant Bed Location and Disassembly Replacing the Process/Regeneration Heater ProceduresReplacement Procedures Replacing/Cleaning the Cooling CoilPage Introduction TroubleshootingProc Blwr Using a Thermocouple Determining Temperature Controller Errors or Sensor ErrorsAppendix Technical SpecificationsAftercooler Design Specifications Drawings and DiagramsHigh Heat Model 180F to 400F Air Flow Schematic Level 1 Spare Parts List Electrical & Mechanical Spare Parts ListHI-CORE Desiccant Dryer 15/30/60 CFM Units 30 CFM 60 CFM 120V Control Common Parts 220V Control Common Parts Dryer Identification Serial Number Tag Returned Material PolicyTechnical Assistance Service DepartmentParts Department Sales Department
Related manuals
Manual 52 pages 3.6 Kb Manual 51 pages 45.86 Kb

882.00291.00 specifications

Sterling 882.00291.00 is a remarkable piece of technology designed to cater to the rigorous demands of modern users who require both utility and aesthetics in their devices. This innovative product is a testament to Sterling's commitment to quality and functionality, combining advanced features with user-friendly designs to enhance the overall experience.

At the heart of the Sterling 882.00291.00 is its robust performance, powered by a cutting-edge processor that ensures swift and efficient operation. Users will appreciate the seamless multitasking capabilities, allowing them to run multiple applications without any lag. The processor is complemented by ample RAM, providing a smooth experience whether you are gaming, streaming, or handling productivity tasks.

One of the standout features of the Sterling 882.00291.00 is its high-resolution display. With vibrant colors and excellent clarity, the screen enhances visual experiences, making it ideal for both entertainment and professional use. Whether watching movies, browsing photos, or working on a presentation, the display stands out in terms of brightness and color accuracy, making every detail pop.

Connectivity is another strong suit of this model. Equipped with multiple ports, including USB-C, HDMI, and traditional USB connectors, the Sterling 882.00291.00 ensures users can connect to a wide array of peripherals and external devices with ease. Furthermore, the inclusion of Bluetooth and Wi-Fi capabilities facilitates quick and reliable wireless connections, making it a versatile choice for those on the go.

Durability is a crucial characteristic that sets the Sterling 882.00291.00 apart from its competitors. The device features a sturdy build quality that can withstand daily wear and tear, making it suitable for both personal and professional environments. Additionally, the device is designed with energy efficiency in mind, offering an extended battery life that supports prolonged use without frequent recharging.

In terms of software, the Sterling 882.00291.00 comes equipped with an intuitive operating system that simplifies navigation and enhances user engagement. The user interface is designed to be accessible, allowing individuals of varying tech-savvy levels to operate the device comfortably. Regular updates ensure that users have access to the latest features and security protections.

In conclusion, the Sterling 882.00291.00 stands out for its blend of performance, connectivity, and durability. With its high-resolution display, robust processor, and thoughtful design, it serves as a reliable companion for anyone looking to enhance their digital experience. Whether for work or play, this device positions itself as a go-to option for those seeking quality and reliability.
Top Page Image Contents