HP Embedded Firewall manual FCC Class B Statement, Interference Handbook

Page 85

D

Regulatory Compliance Information

FCC Class B Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1This device may not cause harmful interference, and

2This device must accept any interference received, including interference that may cause undesired operation.

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules, and the Canadian Department of Communications Equipment Standards entitled, "Digital Apparatus," ICES-003.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from the one that the receiver is connected to.

Consult the dealer or an experienced radio/TV technician for help.

The user may find the following booklet prepared by the Federal Communications Commission helpful:

The Interference Handbook

This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402. Stock No. 004-000-00345-4.

NOTE: In order to maintain compliance with the limits of a Class B digital device, 3Com requires that you use quality interface cables when connecting to this device. Changes or modifications not expressly approved by 3Com could void the user’s authority to operate this equipment. Refer to the manual for specifications on cabling types.

79

Image 85
Contents 10/100 Secure Network Interface Card User GuideUnited States Government Legend Contents Installing and Configuring Data Encryption Offloads Configuring the NIC Running NIC Diagnostics Minimum Installation Requirements Installing and Connecting the NICInstallation Overview Preparing the NIC and the Computer Safety PrecautionsNetwork Environment Cable Required Maximum Cable Length Installing and Connecting the NIC 3CR990B-97 NIC Verifying the Network Driver Installation Installing the Network DriverInstall without Diagnostic Program-installs the driver only Double click Network ConnectionsWindows 2003 Server Driver Installation Windows XP Driver Installation Windows XP Driver Installation Windows 2000 Driver Installation Windows 2000 Driver Installation Click Have Disk Windows NT 4.0 Driver InstallationVerifying the Network Driver Installation Windows 98 SE Driver Installation Windows 98 SE Driver Installation Installing the Driver in Novell NetWare Server 5.1 Novell NetWare Driver InstallationInstallation During Novell OS Installation Identifying the Slot Number Installation with Novell Already InstalledChoose Select a driver Select Save parameters and load driverLoad ODINEB.NLM Verifying or Modifying NIC ParametersRemoving Drivers from Autoexec.ncf Installing the Driver in Novell NetWare Server Page Cd /tmp/3c990/3c990 make Linux 2.4 Driver InstallationLinux 2.4 Driver Installation Offloading Encryption Processing OverviewSelecting Basic or Strong Encryption Processing Creating a Security Policy Configuring IPSec in Windows 2003, Windows XP, and WindowsEncryption Type Level Description Defining the Console Clear the Activate the default response rule check boxCreating the Policy Select IP Security Policy Management, and then click AddBinding the Filter Creating a FilterCreating the Filter Action Enabling Encryption Binding the Filter ActionDisabling Encryption Select Un-assignInstalling and Configuring Data Encryption Offloads About the Advanced Server Features Installing 3Com Advanced Server Features for Windows3Com DynamicAccess Advanced Server Features Failover Load BalancingVLANs Server Features Using Other NICsVerifying the Installation Installing 3Com Advanced Server SoftwarePlanning the Configuration Configuring Groups and VLANsNumber of VLANs Working With Server FeaturesWindows 2003, Windows XP, and Windows Creating a GroupWindows NT Specifying a Dedicated IP Address Adding NICs to a GroupCreating a Vlan Click ConfigureChanging an IP Address Specifying Traffic PrioritiesDisabling Load Balancing for a Group Saving the ConfigurationChanging the Primary NIC Removing a NIC from a GroupSymptomTip Troubleshooting a Load Balancing ConfigurationDisplaying NIC Properties Displaying Group PropertiesDouble-clickNetwork Adapters Enabling Offloads Value Offload Function EnablesConfiguring Offloads for a Group of Different NICs Default NIC Settings Configuring the NICOption Description Settings DisabledAll Configuring the NICMethod Description Requirements Configuration MethodsInstalling the 3Com NIC Diagnostics Program Changing General NIC Configuration SettingsUsing the 3Com NIC Diagnostics Program Starting the 3Com NIC Diagnostics ProgramUsing the 3Com DOS Configuration Program Enabling or Disabling the Boot ROM Setting Configuring the Managed PC Boot Agent MBABooting From the Network BBS BIOS-Compatible PCsDisabling the 3Com Logo Non-BBS BIOS-Compatible PCsInterpreting the NIC LEDs Troubleshooting the NIC3CR990B-97 NIC State MeaningTroubleshooting Problems with the LEDs Viewing the NIC LEDs in the Diagnostics Program3CR990B-FX-97 NIC Accessing the 3Com Knowledgebase Accessing 3Com Support DatabasesAccessing the 3Com NIC Help System Accessing Release Notes and Frequently Asked QuestionsProblems or Error Messages Troubleshooting the NIC InstallationCleaning Up a Failed Installation Tip Description Troubleshooting the Network ConnectionTroubleshooting a Network Connection Troubleshooting Remote Wake-UpRJ-45 Cabling Pinouts Copper NIC Only Troubleshooting HubsWindows 2003, Windows XP, and Windows Removing the Network DriverWindows NT Windows 98 SE From the Start menu, select Settings/Control Panel Removing 3Com DynamicAccess Advanced Server FeaturesNetWare Running the 3Com DOS Diagnostics Program Running NIC DiagnosticsTab Description Running the NIC Diagnostics TestsRunning the NIC Test Running the Network TestClick Perform NIC Test Using the 3Com Icon in the Windows System Tray Viewing the NIC LEDs in the 3Com Diagnostics ProgramViewing Network Statistics Enabling the Icon Removing the 3Com NIC Diagnostics ProgramDisplaying Network Statistics Running NIC Diagnostics Hardware 3CR990B-97 NIC SpecificationsNetwork Interface Standards Conformance3CR990B-FX-97 NIC Specifications Cabling Requirements RJ-45 Connector Pin Assignments About the 3Com DMI Agent Installing the 3Com DMI AgentClick NIC Software Click Install 3Com DMI Agent Now Installing the 3Com DMI AgentSystem Requirements Network Management RequirementsPage Installing the 3Com DMI Agent Obtaining Support for your Product Telephone Technical Support and Repair Contact UsCountry Telephone Number Asia, Pacific Rim Europe, Middle East, and Africa Country Telephone NumberLatin America North America Telephone Support and Repair 1 CountryInterference Handbook FCC Class B StatementFCC Declaration of Conformity MIC Class B Compliance Korea Safety Compliance Statement