HP ep7100 manual Safety information, Regulatory information, LED safety, Mercury safety

Page 74

Reference

Safety information

LED safety

The infrared ports located on the digital projector and remote control are classified as Class 1 LED devices according to International Standard IEC 825-1 (EN60825-1). This device is not considered harmful, but the following precautions are recommended:

■If the unit requires service, contact an authorized HP service center.

■Do not attempt to make any adjustment to the unit.

■Avoid direct eye exposure to the infrared LED beam. Be aware that the beam is invisible light and cannot be seen.

■Do not attempt to view the infrared LED beam with any type of optical device.

Mercury safety

ÅWARNING: This digital projector lamp contains a small amount of mercury. If the lamp breaks, adequately ventilate the area where the breakage occurred. Disposal of the lamp might be regulated due to environmental considerations. For disposal or recycling information, contact your local authorities or the Electronic Industries Alliance at http://www.eiae.org.

Regulatory information

This section presents information that shows how your digital projector complies with regulations in certain regions. Any modifications to your digital projector not expressly approved by HP could void the authority to operate the digital projector in these regions.

U.S.A.

This digital projector has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This digital projector generates, uses, and can radiate radio frequency energy.

If not installed and used in accordance with the instructions, it can cause harmful interference to radio communications. However, there is no guarantee that

74	User’s Guide

Image 74

Contents HP ep7100 Series Home Cinema Digital Projector First Edition July Contents Showing video Index Contents Setting up Safety precautionsWhat’s in the box? Identifying the contents of the box Identifying major components Identifying common featuresProjector at a glance Projector buttons and lights Identifying the projector buttons and lightsBack panel Identifying back panel componentsRemote control Accessories Identifying features of the remote controlSetting up the projector Planning your layoutSetting up Image size diagonal Image size width Distance lens to screen Connecting power Connecting a video source Connecting a component-video source Connecting an S-video source Connecting a composite-video source Connecting a DVI source Connecting a Scart source Connecting a sound system Connecting several video sources Connecting a computer Turning the projector on and off Turning the projector onTurning the projector off Moving the projectorAiming the projector Making basic adjustmentsSelecting a source Adjusting the focus and zoom Changing the picture mode Press menu and go to Picture Customize picture modeAdjusting the shape of the picture Adjusting a slanted picture Adjusting the volumeHiding or showing the picture Showing videoShowing the video source Showing a computer screenShowing video Adjusting the picture Adjusting the projectorAdjusting the picture and sound Adjusting the soundChanging settings using the on-screen menu Using the on-screen menuAdjusting the projector setup Input menu Input menuPicture menu Picture menuSource or each viewing environment. You can also Help menu Setup menuSound menu Adjusting the projector Getting the projector status Cleaning the projector lensMaintaining the projector Replacing the lamp module Replacing the lamp module requires special considerationReplacing the battery in the remote control Maintaining the projector Installing on a table Installing permanentlyInstalling the projector Installing on the ceilingSerial connections Connecting to a room controllerExamples of room controller commands Request *BRT=65CR Room controller commands NotificationCspc Hide Lhrs Shdn Menu Installing permanently If the red temperature light is on or blinking Fixing problemsTroubleshooting suggestions If both red warning lights are blinkingStart-up problems Picture problemsIf the image is too small or too large If the image is out of focusIf an upside-down or reversed image is displayed If the image has slanted sidesIf the projected colors seem completely wrong If the image is stretchedIf the projected colors seem slightly wrong If the image disappears from the computer screen Sound problemsIf a computer display is projected with low resolution If no sound is coming out of the projectorInterruption problems Remote control problemsTesting the projector Press menu and go to Help DiagnosticsFixing problems Contacting HP support Support and warrantySupport Americas Extent of limited warranty Limited warrantyHP digital projector limited warranty statement Obtaining HP repairLimitations of warranty Limitations of liabilityLocal law Support and warranty Reference SpecificationsProjector specifications Operating Video mode compatibility Compatibility Resolution Refresh rates Hz AnalogMercury safety Safety informationLED safety Regulatory informationConnections to peripheral devices CanadaJapan Korea International Declaration of conformity Reference Index Index Index Index Page 5990-3663