Toshiba RAV-SM563AT-E, RAV-SM1102CT-E, RAV-SM1102BT-E, RAV-SM1403UT-E, RAV-SM1402CT-E 122

Page 122

No. Part name

Procedure

Remarks

…Control P.C. 1. Detachment

board

 

1) Perform works of items 1 of • and 1 of

 

 

‚.

 

 

2) Remove connectors which are con-

 

 

nected from the control P.C. board to

 

 

other parts.

 

 

CN33 : Louver motor (5P: White)

 

 

CN34 : Float switch (3P: Red)

 

 

 

Card-edge spacer

 

 

CN41 : Terminal block of remote

 

 

controller (3P: Blue)

 

 

CN68 : Drain pump (3P: Blue)

 

 

CN67 : Terminal block of power supply

 

 

(5P: Black)

 

 

CN101: TC sensor (2P: Black)

 

 

CN102: TCJ sensor (2P: Red)

 

 

CN104: Room temperature sensor

 

 

(2P: Yellow)

 

 

CN333: Power supply of fan motor

 

 

(5P: White)

 

 

CN334: Position detection of fan motor

 

 

(5P: White)

 

 

 

 

 

 

NOTE :

 

 

 

Remove the connector by releasing

 

 

 

locking of the housing.

 

 

 

 

 

 

 

3) Unlock locking of the card-edge spacer

 

 

at 6 positions to remove the control P.C.

 

 

board.

 

2. Attachment

 

 

1) Fix the control P.C. board to the card-

 

 

edge spacer at 6 positions.

 

 

2) Connect the connectors removed in

 

 

item 1 to the original positions.

– 122 –

Page 121 Page 123
Image 122
Page 121 Page 123
Contents AIR-CONDITIONER Contents 10-3 10-110-2 10-4Confirmation of warning label on the main unit Explanation of indicationsExplanation of illustrated marks Indication ExplanationDo not modify the products ∗ For details, refer to the parts listNever recover the refrigerant into the outdoor unit For spare parts, use those specified ∗Side Check the following items after reinstallationMetal section Earth position Limit even if the refrigerant leaksCopper pipe Piping Safety Caution Concerned to New RefrigerantPipe Materials Flare nutUsed tool Usage General tools Conventional tools can be usedR410A Conventional air Digital Inverter Indoor UnitWay Air Discharge Cassette Type Super Digital Inverter SP562AT-E SP802AT-EConcealed Duct Type RAV SM562BT-E SM802BT-ESuper Digital Inverter Under Ceiling Type RAV SM562CT-E SM802CT-ERevised Mar Twin Type Indoor unitSP1402AT-E SP1102AT-E RAV SM563AT-E SM803AT-E SP562AT-E SP802AT-E Cooling Heating Operation characteristic curve Digital InverterRAV-SM563AT-E, RAV-SM803AT-E CurrentOperation characteristic curve Super Digital Inverter RAV-SP1102AT-EOutdoor temp. ˚C Capacity variation ratio according to temperatureRatio Capacity High PressureTap Low StaticStatic Pressure Tap Tap LowRAV-SM563UT-E, RAV-SM803UT-E 35˚RAV-SM1103UT-E, RAV-SM1403UT-E, RAV-SP1102UT-E 188Dimension Suction port canvas Separate soldRAV-SM562CT-E, RAV-SM802CT-E, RAV-SM1102CT-E, RAV-SM1402CT-E Space required for service 365 RAV-SP1102AT-E, RAV-SP1402AT-E Outdoor unit Indoor unitRAV-SM563UT-E, RAV-SM562BT-E, RAV-SM562CT-E / RAV-SM563AT-E RAV-SM803UT-E, RAV-SM802BT-E, RAV-SM802CT-E / RAV-SM803AT-E Min. Max 5m 50m Ball valve Packed valve Outer dia. Ø a Outdoor unitDistributor TCJ sensor 25 × L180Outer dia. Ø B Strainer RAV-SM563UT-E, RAV-SM562BT-E, RAV-SM562CT-E / RAV-SP562AT-E TCJRAV-SM803UT-E, RAV-SM802BT-E, RAV-SM802CT-E / RAV-SP802AT-E 1500cc R410A 2.1 kg Cooling HeatingTCJ sensor Distributor Compressor DA420A3F 21M R410A 2.95kg Cooling HeatingL210 FP1.3 flat fin Inside 2500cc RotaryColor LM1 3LM2 3 IdentificationIndoor Unit ColorIdentification LM 3MCC-5009 Outdoor Unit WiringDiagram BoardMCC-1531 BoardMCC-1438 SUB P.C. boardRAV-SP562AT-E, RAV-SP802AT-E BLK Black WHI White BLU Blue BRN Brown Parts name Type Specifications MP24Z2N RAV-SM563AT-E RAV-SM803AT-ECAM-MD12TF-8 TCB-DP22CE2 Drain up kit RBC-U21PG W -E2 Ceiling panelSafety During Installation/Servicing Piping Materials and Joints UsedOuter diameter mm R410A R22 Processing of Piping Materials1 Thicknesses of annealed copper pipes Thickness mm 12.7 15.9R22 clutch type Clutch type Wing nut type Flare tool for Conventional flare toolR410A clutch type Clutch type Wing nut type Diameter Width mmNm kgfm 43˚to 45˚13.0 13.5 12.7 16.2 16.0 12.9 15.9 19.4 19.0 23.3 24.0 19.2 Wrenches available on the marketRequired Tools Refer to the 4. ToolsMaterials for Brazing Silver brazing filler Low temperature brazing fillerFlux Reason why flux is necessary Phosphor bronze brazing fillerActivated flux Characteristics required for fluxTypes of flux Noncorrosive flux Piping materials for brazing and used brazing filler/fluxCuring of pipes Basic conditions need to reuse the existing pipeBranching pipe for simultaneous operation system Restricted items to use the existing pipesExisting pipe no * Use a new pipes When recovering refrigerant in case of reinstalla Recovery method of refrigerant for RAV-SM563AT-E, SM803AT-EWork procedure Main Sub master remote controller Indoor Control CircuitOutline of specifications Remarks Heating Auto Setting at shipmentCool OperationHeat Control temp C All modes ArningCooling/dry operation In heating/fan operation Frequency fixed In case of wired remote controller Operation Prohibited Last push priorityCenter Normal control Ay Air Indoor PrintCircuit Board Concealed Duct Type / Under Ceiling TypeOutdoor Controls Indoor P.C. Board Optional Connector SpecificationsFunction Connector Pin Specifications Remarks AppliedP.C board MCC-5009SM803AT-E Iewed from partsEEPROM-IC RAV MCC-1531SP1402AT-E Ipdu MCC-1438RAV -SP562AT-E, RAV RAV -SM1103AT-E, RAV -SM1403AT-EDischarge temperature release control Current release controlAllocations of fan tap revolutions rpm Outdoor fan controlOperation with WE TE ˚C TD ˚CTo ˚C Coil heating controlTrouble of TE sensor TE ˚CTE ºC Defrost controlStart of heating operation ZoneTroubleshooting procedure Summary of TroubleshootingBefore troubleshooting Ired remote controller typeTrouble Confirmation of lamp display Check Code List Error mode detected by indoor and outdoor unitsCause of operation Status of air Condition Error mode detected by remote controller Error mode detected by central remote controllerType B Error Mode Detected by LED on Outdoor P.C. BoardType a E09 error Troubleshooting Procedure for Each Check CodeE01 error Check CodeE04 error E08, L03, L07, L08 error E10 errorE18 error L09 errorP10 error L20 errorL30 error F10 errorCN334 P12 error Only for 4-way air discharge cassette type modelsCN333 P22 error P19 error F02 errorF01 error P26 errorP29 error H03 errorF08 error F06 errorF04 error L29 error H02 errorP03 error H01 errorP04 error C06 error Central controller Same as others Correct connection of connectorP31 error Sub indoor unit E03 error Master indoor unitF29 error / 12 error 100Caracteristics-3 101TA sensor TC, TCJ sensor Caracteristics-2 Caracteristics-1 20 TE, TO, TS sensorReplacement Procedure 102Contents R1 Readout of the setup data from EepromR2 Replacement of service P.C. board 103R3 Writing of the setup contents to Eeprom Type Item code Memorandum for setup contents Item code table Example105 Indoor unit capacity Item code106 Test Run Setup on Remote ControllerWired remote controller RAV-SM563UT-E, RAV-SM803UT-E, RAV-SM562BT-E, RAV-SM802BT-EReturn Dip switch of the sensor section as before Use either Cool or Heat operation mode for test operationConditioner from the wireless remote controller 107Case of wireless remote controller 108109 Item No. DN table Selection of functionSetup method Cabling and Setting of Remote Controller ControlIndoor unit is controlled by 2 remote controllers 110111 Monitor Function of Remote Controller SwitchCall of sensor temperature display Contents 112 Calling of error history ContentsOrder to monitor another error history, push Group control operation113 Setup at Local Site / OthersTCC-LINK Adapter For TCC-LINK Central Control 114 Wiring SpecificationsC. Board Switch SW01 Setup SizeHow to set up central control address number 115Item code Data at shipment Setup data range Address SetupAddress setup procedure 116Only turning on source power supply Automatic completion Address Setup & Group ControlSystem configuration Automatic address example from unset address No miscabling118 Manual setting from remote controllerEND 119 Detachment No. Part name Procedure Remarks120 Attachment121 122 † Fan motor 1. Detachment CN102 TCJ sensor 2P Red CN333 Power supply of fan motor123 Remove nuts fixing the fan motor to Remove it124 ‡ Drain pan 1. DetachmentFix the drain pump assembly as before Assembly Perform works of items 1 of , 1 of ‚Body 1 position, and then remove Assembly. Ø4 × 8, 3 pcs 125Heat Part name Procedure Remarks126 127 128 129 130 „ Multi blade fan Remove the suction grille Motor Remove the connector of the fan131 Case side. Then fans come off132 133 Heat exchanger support134 Procedure Remarks 135136 137 By hands so that the fan motor does not 138Take off fixed screw for the valve mounting Fall Tighten the flange nut with torque 4.9Nm 50kgf/cm139 Perform works of items 1 of , and ‚ 140Fan guard With minus screwdriver along withRemove the upper cabinet. ST1T Ø4 × 10L, 6 pcs 141Clamp Fin guard Heat exchanger ST1T Ø4 × 10, 2 pcs 142Discharge port cabinet for the heat 143 144 145 Loosen the flange nut by turning clock 146Motor and the propeller fan 147 148 149 Product150 Put the upper left side of the air-outlet 151‚ Air-outlet cabinet Cabinet on the end plate of heat exCN702 PMV Pulse Motor Valve coil 152„ Inverter Perform the works in 1 of and ƒ Remove connectors and lead wires 153154 Case of RAV-SP1402AT-E 155Case of RAV-SP1102AT-E ‰ PMV coil 156Pay attention that 4-way valve or PMV is 157 Electric parts box as shown below so that 158Reactor Perform works of items to „ They do not come to contact with the reac Tor225 209 208 233231 159402 404 401 405 403 160224 212 205 231 161162 229 224 212 211 225 209 202 226208 216, 218 205 230 213, 214, 220 223 207 232 231164 RBC-U21PG W E2 304 311 306 305 301 307 302 303 310 313 308 309165 RAV-SM562BT-E 902166 901, 902, 903 43196012 Bushing 43166002 Remote Controller904 167RAV-SM1102BT-E, RAV-SM1402BT-E 904 901, 902168 \Location Part Description 402 404 403 406 405401407169 36, 37, 38,39, 54 44, 4522, 23 33, 34, 35,53, 56171 404 43158193 Reactor 404401 407 403 406 402 405172 Muffler 21, 22 14, 16, 17 13, 15, 1910, 32 173705 701 702 708 707 706 710 174RAV-SM1103AT-E, RAV-SM1403AT-E 3332 15, 16175 707 708 706 704 703 701 705 702 710 17643146695 Valve, Pulse, Modulating 21,22 16,17177 704 707 178Inverter 26,27 23,24 28,29 179180 710 706 704709 181 Replacement of Main Parts Sold SeparatelyDrain up Kit TCB-DP22CE2RBC-AX22CE2 Wireless Remote Control Kit182 Part name ’ty Specifications/Vendor Remarks Required parts for installation work RecommendationThis is on installation for 2 HP and 3 HP Products 183184 Required tools for installation workPart name Specifications Usage Cord heater installation wiring diagram 185186 Cord heater installation work procedurePhoto / Explanatory diagram Procedure 187 Remove the motor base assembly, partition plateAssembly and the sound insulation board Remove the fixing screws of the heat exchanger188 189 Photo / Explanatory diagram Procedure Assembly 190191 Drawing of thermostat fixing plateMaterial SGCC-Z08, Thickness 0.8t Ø3.4 burring hole Upward Ø3.4 burring hole DownwardBase Plate 192RAV-SM1103AT-E, RAV-SM1403AT-E 193Check of Concentration Limit Toshiba Carrier Corporation
Related manuals
Manual 18 pages 35.13 Kb

RAV-SP1102UT-E, RAV-SM562BT-E, RAV-SM562CT-E, RAV-SM563AT-E, RAV-SM802BT-E specifications

Toshiba, a prominent player in the HVAC sector, has engineered a range of advanced air conditioning systems that cater to diverse environments and needs. Among their standout offerings are the RAV-SM562BT-E, RAV-SM1102CT-E, RAV-SM563AT-E, RAV-SM1403UT-E, and RAV-SM803UT-E models. Each of these systems embodies Toshiba's commitment to energy efficiency, innovative technology, and user-centric design.

The RAV-SM562BT-E model is designed for residential and light commercial use, boasting a cooling capacity of 5.6 kW and a heating capacity of 6.7 kW. It incorporates Toshiba’s advanced inverter technology, ensuring optimal performance and reduced energy consumption. The unit features a sleek, modern design and operates quietly, making it perfect for environments where noise levels must be controlled.

Next in line is the RAV-SM1102CT-E, which excels in larger commercial spaces. With a remarkable cooling output of 11.2 kW and heating performance to match, this unit is engineered for heavy-duty usage. It employs a multi-split system, allowing several indoor units to connect to a single outdoor unit. This provides homes or businesses with flexible installation options without sacrificing comfort or style.

The RAV-SM563AT-E model presents a perfect blend of efficiency and effectiveness, focusing on eco-friendliness. With an impressive seasonal energy efficiency ratio (SEER), it minimizes energy bills while maintaining superior performance. This model is equipped with advanced filtration technology that not only cools or heats the air but also improves indoor air quality by capturing dust and allergens.

Designed for high-performance requirements, the RAV-SM1403UT-E offers cooling and heating capacities of 14.0 kW. This unit is hardy enough for industrial applications but remains efficient and easy to operate. The incorporation of Toshiba’s Smart Control technology allows users to manage their systems remotely, enhancing convenience.

The RAV-SM803UT-E completes the lineup, combining 8.0 kW cooling and heating outputs with cutting-edge technology. It features adaptive comfort control, which adjusts the temperature based on occupancy and external conditions, ensuring optimal comfort while maintaining energy efficiency.

In conclusion, Toshiba's range of RAV-SM series models offers innovative features, advanced technology, and effective performance. These models not only meet the demands of modern spaces but also shine in energy efficiency, making them excellent choices for both residential and commercial applications. By addressing the diverse requirements of users, Toshiba continues to uphold its reputation as a leader in HVAC solutions.
Top Page Image Contents