York DGPA070ABTA warranty Installation of Screw Abachmentduct Connector, Unitary Products Group

Page 10

035-16328-Rev002.C (0902)

 

LOCATOR BRACKET

 

 

 

NAILS, FLAT HEAD SCREWS

 

 

OR STAPLES

_

NAI L_,AFLEATHEAD SC R EWS

BEND TABS UNDER

OPENING TO

 

 

 

 

SECURE TO THE

 

FLOOR

SUPPLY DUCT

 

 

SUPPLY DUCT

FIGURE tl : Duct Connector Screw Attachment

INSTALLATION OF SCREW A'B'ACHMENTDUCT

CONNECTOR

1, Make floor cut out as shown in Figure 9.

2.Determine the depth of the floor cavity from the surface of the floor to the top of the supply air duct and select the appropriate duct connector from the chart.

3.Place locating bracket (supplied with the duct connector) to the back edge of the floor opening. See Figure 11.

4.Apply a water based duct sealant to the 1/2" supply duct attachment flange of the duct connector.

5.Determine which of the four positions the duct connector

best centers over the supply duct and insert it through the floor cutout.

6.When propedy aligned with the supply duct, secure the duct connector to the floor with nails, flat head screws or staples.

7.Use screws as required to secure the duct connector to the supply duct.

8.Cut out the opening to the supply duct. If sealant was not used, the instaner should tape the mating flanges to pro- vide s good air seal.

NOTE: Duct sealant and tape must be classified as meeting HUD Standard 3280.715, U.L. Standard 181A.

If tape is used to provide a better air seal, it should be a type approved by the applicable national or local codes.

SUPPLY DUCT

FIGURE t2 : Duct Connector Tab Attachment

INSTALLATION OF TAB ATTACHMENT DUCT

CONNECTORS

1.Make floor cut out as shown in Figure 9.

2.Determine the depth of the floor cavity from the surface of the floor to the top of the supply air duct and select the appropriate duct connector from the chart.

3.Place locating bracket (supplied with the duct connector)

to the rear of the floor area for the furnace. See Figure

12.

4.Determine which of the four positions the duct connector

best centers over the supply duct and insert it through the floor cutout.

5.Mark cut-out location on the supply duct and remove the duct connector.

6.Cut out the opening to the supply duct.

7.Bend tabs down through and back up under the supply duct.

8.Secure the duct connector to the floor with nails, flat head screws or staples.

The duct connector is designed for use on ducts down to 12" in width. When using the connector on smaller width ducts, there will not be sufficientclearance to bend the tabs on two sides of the duct connector.

In such cases the tabs may be attached to the sides of the duct by using sheet metal screws or other suitable fasteners. Holes for sheet metal screws are provided in three (3) tabs on each side of the duct connector. If more than 3 tabs need to be used to provide a more secure and air tight connection, the remaining tabs can also be fastened to the duct with screws after drilling the required screw holes.

10

Unitary Products Group

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Models DGAA, DGAH, DGPA, and Dgph For Installation Manufactured Mobile HomesSealed Combustion Downflow GAS Furnace Furnace START-UP Check ListFurnace Specifications Electrical SpecificationsGeneral Information Installation StandardsHigh Altitude Installation CodecomplianceAIR Distribution Systems Closet InstallationsReturn AIR Requirements Transition ductDoor Below the top of the furnace casing7900-7771/C * White Installation in Snow Regions Existing Furnace ReplacementNEW Home Installation Roof Jack4900-7141/C 4000-6141/A 4000-6101/A4000-61211A 4000-6151/ARoof Jack With Removable Crowns Unitary Products Group Rear Wall Enclosure Ceiling CUT-OUT Duct ConnectorsDuct Connector Dimensions Supply DuctUnitary Products Group Installation of Screw Abachmentduct ConnectorInstallation of TAB Attachment Duct Connectors Locator BracketInstallation of the Furnace Tened to the furnaceConnect Thermostat Wires Electrical WiringConnect Power Supply Wires Ceiling RingsNot Factoryinstalled Wall ThermostatWiring Diagrams Limitswitch Manual Reset WHT Limit SwitciRED AMP Fuse Auto Reset NEU WHT SwitchORG Blower Relay GRY BLEND-AIR Limit Control BOX Switch If EquippedBLU WHT Auto Reset Limit Switch System LineAuto Reset Limit Switch Pressure AJC Condensing Unit Contactor NEU WHT SwitchFAN Switch Blower ORG Motor Combustion Relay GRYIncoming Power Must be Polarized Observe Color Coding Ca L oGAS Piping Installation and Checking of GAS LinePilot Adjustment Observing Burner OperationFinish and Trim Final Procedure Install Furnace DoorsFurnace and AIR Conditioner Base DuctNatural GAS High Altitude Deration ChartPropane GAS DGAA,DGAH Repair Parts ListDGAA, Dgah DGPA, Dgph Control BOX DetailDgaa Description DGAA056BDTA DGAA070BDTA DGAA077BDTA DGAA09OBDTAItemdescription DgahDGAH056BBSA DGAH077BBSA Dgpa Description DGPA086ABTA DGPA070ABTA DGPA077ABTA DGPA090ABTADescription DGPH056ABTA DGPH070ABTA DGPH077ABT DgphDGPH090ABTA Accessory Parts List Description Dgaa Dgah Dgpa Dgph ModelSupersedes

DGPA056ABTA, DGAAO77BDTA, DGAHO77BBSA, DGPA070ABTA, DGPA090ABTA specifications

York DGPA070ABTA, DGAA056BDTA, DGPA090ABTA, DGPA077ABTA, and DGPH077ABTA are part of York’s latest series of air conditioning and heat pump units, designed to meet the evolving demands of residential and commercial applications. These models combine efficiency with advanced technology to provide optimal climate control throughout the year.

The DGPA070ABTA stands out for its impressive cooling capacity, making it suitable for medium-sized spaces. Equipped with a high seasonal energy efficiency ratio (SEER), it maximizes cooling performance while minimizing energy consumption. This model is integrated with advanced inverter technology, allowing for variable speed operation. This means that the compressor can adjust its speed based on the cooling or heating demand, ensuring consistent temperatures and reduced energy waste.

The DGAA056BDTA model is tailored for users seeking a balance between performance and efficiency. This air conditioner features a dual-stage compressor that enables it to operate at reduced capacity during milder conditions, resulting in lower energy costs. Its compact design is ideal for installations where space is limited, and it offers a whisper-quiet operation, making it particularly attractive for residential settings.

Next is the DGPA090ABTA, which boasts one of the highest capacities in this range, making it capable of cooling larger areas effectively. It employs a state-of-the-art refrigerant that not only improves efficiency but also reduces environmental impact. This model's smart grid compatibility allows for easier integration with home automation systems, enabling users to monitor and control their cooling systems remotely.

The DGPA077ABTA serves as a versatile option for both residential and commercial users. This model features a robust build designed for durability and longevity. With its advanced filtration system, it ensures cleaner air circulation, enhancing indoor air quality. It also has programmable settings, allowing users to define schedules that align with their lifestyle.

Finally, the DGPH077ABTA model is a high-efficiency heat pump, providing both heating and cooling capabilities. This dual functionality makes it an attractive choice for regions with variable climates. The heat pump operates efficiently even in low temperatures, ensuring comfort no matter the season.

In summary, the York DGPA070ABTA, DGAA056BDTA, DGPA090ABTA, DGPA077ABTA, and DGPH077ABTA units encapsulate the brand’s commitment to innovation, efficiency, and user-centric design. These models utilize advanced technologies to ensure dependable performance, enhancing indoor comfort while being mindful of energy consumption and environmental impacts.
Top Page Image Contents