York DGAAO77BDTA, DGPHO56ABTA warranty Ceiling Rings, Electrical Wiring, Connect Power Supply Wires

Page 12

035-16328-092 Rev. C (0902)

CEILING RINGS

The coiling ring is to meet fire stop requirements. Accessory Ceiling Ring (PIN 7660-2841) may be used, (See Figure 15) or the manufactured home manufacturer or the installer may use other approved methods to stop fire.

If required, three (3) sections of Accossory Ring may be used

as shown in Figure 15 to provide closer clearance around roof jack,

AB

FIGURE 15 : Ceiling Rings

ELECTRICAL WIRING

IlIA CAUTIiQN

TO INSTALLER: Incoming power must be polar- ized. Observe color coding.

AWARNING!

SHOCK HAZARD - DISCONNECT ELECTRI- CAL POWER SUPPLY TO THE UNIT BEFORE SERVICING TO AVOID THE POSSIBILITY OF

SHOCK INJURY OR DAMAGE TO THE EQUIP- MENT

CONNECT POWER SUPPLY WIRES

1.Remove the field wiring cover.

2, Insert 115 volt wires through the large plastic bushing on the left side of the furnace (See Figure 16). If conduit is used it should be secured to the control box.

3.Connect the "hot" wire to the BLACK pigtail lead, and the "neutral" wire to the WHITE pigtail lead. Secure all con- nections with suitable wire nuts and wrap with electrical tape.

4.Connect the "ground" wire to the grounding screw.

5.Reinstall the control panel cover and secure mounting

screw,

CONNECT THERMOSTAT WIRES

1.Insert 24 voltwires throughthe small plastic bushing just above the control panel.

2.Connect the thermostat wires to the furnace low voltage pigtails. See Figure17 (heating only) and Figure 18 (heating and cooling).

3.

Connect low-voltage circuit to the wall thermostat pig- tails.

NOTE: Five-conductorthermostat cable is recommended for

all installations to allow easy installation of an air conditioning system at a later time.

Eighteen gauge thermostat wire is highly recommended.

Smaller gauge thermostatwire may be used only if the guide- line below is followed.

THERMOSTAT WIRE

THERMOSTAT

LENGTH

(FURNACE

TO

WlRE GAUGE

THERMOSTAT)

 

 

 

0

- 45

feet

 

22

0

- 70

feet

 

20

Do not use thermostat wire smaller than 22 gauge. If thermo-

stat wire smaller than 18 gauge is used, pay particular atten- tion that the connections between the different wire sizes are

tight.

Operational problems may be caused by loose connections or by the use of thermostat wire that is too small to carry the

required load. Any such problems are the responsibility of the installer.

Aseparate 115 _/A.C. supply circuit must be used for the fur-

naco. The circuit should be protected by a 15 amp fuse or cir- cuit breaker.

J

THIS SCREW DOES

 

NOT NEED TO BE

 

REMOVED IN ORDER

 

TO REMOVE THE

NOTE:

FIELD WIRING COVER.

Cover should

(JUST LOOSEN).

not be removed

 

except when

 

servicing the

 

controls.

 

a

FIGURE 16 : Field Wiring

12

Unitary Products Group

Page 11 Page 13
Image 12
Page 11 Page 13
Contents For Installation Manufactured Mobile Homes Sealed Combustion Downflow GAS FurnaceModels DGAA, DGAH, DGPA, and Dgph Furnace START-UP Check ListFurnace Specifications Electrical SpecificationsInstallation Standards High Altitude InstallationGeneral Information CodecomplianceCloset Installations Return AIR RequirementsAIR Distribution Systems Transition ductBelow the top of the furnace casing Door7900-7771/C * White Existing Furnace Replacement NEW Home InstallationInstallation in Snow Regions Roof Jack4000-6101/A 4000-61211A4900-7141/C 4000-6141/A 4000-6151/ARoof Jack With Removable Crowns Unitary Products Group Duct Connectors Duct Connector DimensionsRear Wall Enclosure Ceiling CUT-OUT Supply DuctInstallation of Screw Abachmentduct Connector Installation of TAB Attachment Duct ConnectorsUnitary Products Group Locator BracketInstallation of the Furnace Tened to the furnaceElectrical Wiring Connect Power Supply WiresConnect Thermostat Wires Ceiling RingsNot Factoryinstalled Wall ThermostatWiring Diagrams Manual Reset WHT Limit Switci RED AMP Fuse Auto ResetLimitswitch NEU WHT SwitchBLEND-AIR Limit Control BOX Switch If Equipped BLU WHT Auto Reset Limit Switch SystemORG Blower Relay GRY LineAJC Condensing Unit Contactor NEU WHT Switch FAN SwitchAuto Reset Limit Switch Pressure Blower ORG Motor Combustion Relay GRYIncoming Power Must be Polarized Observe Color Coding Ca L oInstallation and Checking of GAS Line Pilot AdjustmentGAS Piping Observing Burner OperationFinal Procedure Install Furnace Doors Furnace and AIR ConditionerFinish and Trim Base DuctHigh Altitude Deration Chart Natural GASPropane GAS Repair Parts List DGAA, Dgah DGPA, DgphDGAA,DGAH Control BOX DetailDgaa Description DGAA056BDTA DGAA070BDTA DGAA077BDTA DGAA09OBDTADgah ItemdescriptionDGAH056BBSA DGAH077BBSA Dgpa Description DGPA086ABTA DGPA070ABTA DGPA077ABTA DGPA090ABTADgph Description DGPH056ABTA DGPH070ABTA DGPH077ABTDGPH090ABTA Accessory Parts List Description Dgaa Dgah Dgpa Dgph ModelSupersedes

DGPA056ABTA, DGAAO77BDTA, DGAHO77BBSA, DGPA070ABTA, DGPA090ABTA specifications

York DGPA070ABTA, DGAA056BDTA, DGPA090ABTA, DGPA077ABTA, and DGPH077ABTA are part of York’s latest series of air conditioning and heat pump units, designed to meet the evolving demands of residential and commercial applications. These models combine efficiency with advanced technology to provide optimal climate control throughout the year.

The DGPA070ABTA stands out for its impressive cooling capacity, making it suitable for medium-sized spaces. Equipped with a high seasonal energy efficiency ratio (SEER), it maximizes cooling performance while minimizing energy consumption. This model is integrated with advanced inverter technology, allowing for variable speed operation. This means that the compressor can adjust its speed based on the cooling or heating demand, ensuring consistent temperatures and reduced energy waste.

The DGAA056BDTA model is tailored for users seeking a balance between performance and efficiency. This air conditioner features a dual-stage compressor that enables it to operate at reduced capacity during milder conditions, resulting in lower energy costs. Its compact design is ideal for installations where space is limited, and it offers a whisper-quiet operation, making it particularly attractive for residential settings.

Next is the DGPA090ABTA, which boasts one of the highest capacities in this range, making it capable of cooling larger areas effectively. It employs a state-of-the-art refrigerant that not only improves efficiency but also reduces environmental impact. This model's smart grid compatibility allows for easier integration with home automation systems, enabling users to monitor and control their cooling systems remotely.

The DGPA077ABTA serves as a versatile option for both residential and commercial users. This model features a robust build designed for durability and longevity. With its advanced filtration system, it ensures cleaner air circulation, enhancing indoor air quality. It also has programmable settings, allowing users to define schedules that align with their lifestyle.

Finally, the DGPH077ABTA model is a high-efficiency heat pump, providing both heating and cooling capabilities. This dual functionality makes it an attractive choice for regions with variable climates. The heat pump operates efficiently even in low temperatures, ensuring comfort no matter the season.

In summary, the York DGPA070ABTA, DGAA056BDTA, DGPA090ABTA, DGPA077ABTA, and DGPH077ABTA units encapsulate the brand’s commitment to innovation, efficiency, and user-centric design. These models utilize advanced technologies to ensure dependable performance, enhancing indoor comfort while being mindful of energy consumption and environmental impacts.
Top Page Image Contents