HP EMS HARDWARE S B6191-90028 manual Setting Default Description Value, This setting is required

Page 105

Special Procedures

Fibre Channel Arbitrated Loop Hub Monitor

•Repeat Frequency: 1 day (1440 minutes)

•Severity Action: Notify for all levels

The hub monitor also uses the following settings to configure the SNMP environment used by the hub. Note that two of these settings (HUB_COUNT and HUB_X_IP_ADDRESS) are required to indicate to the monitor what hubs should monitored. Changes that involve adding or deleting hubs to the configuration file while the monitor is running will be invoked at the next polling interval, or following the selection of the (E)nable Monitoring option from the Hardware Monitoring Request Manager (monconfig).

 

 

Table 6-1 PSM Configuration File Fields

 

 

 

Setting

Default

Description

 

Value

 

 

 

 

HUB_COUNT value

none

Identifies the number of hubs (value) the monitor will

 

 

be responsible for monitoring.

 

 

This setting is required.

 

 

 

HUB_X_IP_ADDRESS IP_address

none

Identifies the IP address for each hub the monitor will

 

 

monitor. The “X” placeholder is replaced by the number

 

 

assigned to the hub, and “IP_address” is replaced by the

 

 

IP address of the hub. There must be a separate setting

 

 

for each hub.

 

 

This setting is required.

 

 

 

SITE_SNMP_GET_COMMUNITY

public

These settings define the SNMP community assigned to

text

 

the hubs being monitored. The SITE setting is used for

HUB_X_SNMP_GET_COMMUNITY

 

all hubs, unless overridden by a HUB_X setting for the

text

 

specific hub identified by X.

 

 

The text string cannot contain embedded spaces.

 

 

 

SITE_LOCATION text

none

These settings define the text string used to identify the

HUB_X_LOCATION text

 

hub location in log messages. The SITE setting is used

 

 

for all hubs, unless overridden by a HUB_X setting for

 

 

the specific hub identified by X.

 

 

The text string cannot contain embedded spaces.

 

 

 

SITE_CONTACT text

none

These settings define the text string used to identify the

HUB_X_CONTACT text

 

contact person in log messages. The SITE setting is

 

 

used for all hubs, unless overridden by a HUB_X setting

 

 

for the specific hub identified by X.

 

 

The text string cannot contain embedded spaces.

 

 

 

SITE_SNMP_RETRY value

3

These settings define the SNMP retry value in seconds.

HUB_X_SNMP_RETRY value

 

The SITE setting is used for all hubs, unless overridden

 

 

by a HUB_X setting for the specific hub identified by X.

 

 

Valid values are 1 - 5.

 

 

 

SITE_SNMP_TIMEOUT value

2

These settings define the SNMP timeout value in

HUB_X_SNMP_ TIMEOUT value

 

seconds. The SITE setting is used for all hubs, unless

 

 

overridden by a HUB_X setting for the specific hub

 

 

identified by X.

 

 

Valid values are 1 - 5.

 

 

 

Chapter 6

105

Page 104 Page 106
Image 105
Page 104 Page 106
Contents Manufacturing Part Number B6191-90028 September EMS Hardware Monitors Users GuideLegal Notices Printing History Page Contents Hardware Monitor Configuration Files Using the Peripheral Status MonitorSpecial Procedures Contents About This Manual Related Web Site Introduction Hardware Monitoring Overview What is Hardware Monitoring?Components Involved in Hardware Monitoring How Does Hardware Monitoring Work?Benefits of Hardware Monitoring Products Supported by Hardware Monitors Tips for Hardware Monitoring Hardware Monitoring Terms Hardware Monitoring TermsTerm Definition Hardware Monitoring Terms Introduction Hardware Monitoring Overview Chapter Installing and Using Monitors Steps Involved Steps for Installing and Configuring Hardware Monitoring Supported System Configuration Installing EMS Hardware MonitorsRemoving EMS Hardware Monitors Checking for Special Requirements Disk ArraysProduct Model/Product Special Number Requirements Tape Products all supported by the Scsi Tape Devices Monitor Disk ProductsFibre Channel Scsi Multiplexers High Availability Storage SystemsFibre Channel Adapters Fibre Channel Arbitrated Loop FC-AL HubProduct Model/Product Special Requirements Number Fibre Channel Switch MemorySystem Others Interface CardsUsing Hardware Monitoring Requests What Is a Monitoring Request?Some Monitoring Request Examples Building a Monitoring Request To run the Monitoring Request Manager, type Running the Monitoring Request ManagerEnabling Hardware Event Monitoring Default Monitoring Requests 13 Default Monitoring Requests for Each MonitorSeverity Levels Notification Method To list the descriptions of available monitors Listing Monitor DescriptionsTo view or show the current monitoring requests Viewing Current Monitoring RequestsTo add a monitoring request Adding a Monitoring RequestSetting Description 14 Monitoring Requests Configuration Settings15 Event Severity Levels Event Description MC/ServiceGuard Severity Response LevelEvent Severity Levels Example of Adding a Monitoring Request == ADD Comment To modify a monitoring request Modifying Monitoring RequestsVerifying Hardware Event Monitoring Events = Checking Detailed Monitoring StatusSample Event Message Retrieving and Interpreting Event MessagesTo delete a monitoring request Deleting Monitoring RequestsDisabling Hardware Event Monitoring To disable hardware event monitoringDetailed Description Hardware Monitoring Architecture Detailed Picture of Hardware MonitoringHardware Monitoring Request Manager Components from Three Different ApplicationsEMS Hardware Event Monitor Polling or Asynchronous?Startup Client Peripheral Status Monitor PSM Event Monitoring Service EMSFile Locations 1File LocationsDirectories and Files Description Monitoring Startup Process Startup Process in DetailDisabling Monitoring Event Decoding Asynchronous Event Detection in DetailAsynchronous Event Detection Process FC-AL Hub and FC Switch Polling Processes Event Polling in DetailMemory Monitor Polling Monitoring Polling Process Memory Monitor Polling Process Detailed Picture of Hardware Monitoring Chapter Using the Peripheral Status Monitor Peripheral Status Monitor Overview How Does the PSM Work? Peripheral Status Monitor PSM States PSM ComponentsPSM Resource Paths PSM StatusHow Does the PSM Work? Chapter To create a package resource dependency Configuring Package Dependencies using SAMResourcepollinginterval Resourceupvalue =UP Creating EMS Monitoring Requests for PSM To create a PSM monitoring requestFrom the Actions menu select Add Monitoring Request Setting the Polling Interval Polling Interval Specifying When to Send Event NotifyMonitoring Request Parameters Determining the Frequency of Events OptionsOpcmsg ITO Selecting Protocols for Sending Events Notify ViaCritical Major Minor Normal To set the opcmsg ITOTCP and UDP To set the Snmp trapTo set the TCP or UDP conditions To set for email notificationAdding a Notification Comment Comment Copying Monitoring Requests To change the monitoring parameters of a request To remove monitoring requests Removing Monitoring RequestsViewing Monitoring Requests To view the parameters for a monitoring requestFrom the Actions menu select View Monitoring Request Using the setfixed Utility to Restore Hardware UP State To restore the operating state of a resource to UPExample 4-1 Example of Using setfixed Using the Peripheral Status Monitor Hardware Monitor Configuration Files Monitor Configuration Files Setting Values Description Monitor Configuration File EntriesFile Names File FormatEventnum must be a Interval must be aFrequency must be a Event Definition Sample Global Configuration FileSeverity Action Polling Interval= Communication Device Sample Monitor-Specific Configuration File#POLLINTERVAL Startup Configuration File Keyword Values Description Startup Configuration File EntriesUDP Default File Entries Default Monitoring RequestsDescription Entry Peripheral Status Monitor PSM Configuration File Considerations for Modifying the PSM Configuration File Monitorresourcename PSM Configuration File FieldsCritical Downseverityope Example File Entries Special Procedures Fibre Channel Arbitrated Loop Hub Monitor Configuring the FC-AL Monitor Configuration File Initial Monitor ConfigurationAdding or Removing an FC-AL Hub Configuration FilesThis setting is required Setting Default Description ValuePSM Configuration File Fibre Channel Switch Monitor Configuring the FC Switch Monitor Configuration File Adding or Removing an FC SwitchChanging the FC Switch Monitoring Configuration 2PSM Configuration File Fields Special Procedures 112 Index 114 115
Top Page Image Contents