HP LTO 4 SCSI, LTO 4 FC, LTO 4 SAS manual

Page 85

	Flag	Type	Set	Recommended Host Message		Cause
51	Tape directory	W		The tape directory on the tape		An error has occurred
	invalid at			cartridge just unloaded has been		preventing the tape directory
	unload			corrupted. File search performance		being updated on unload.
				will be degraded. The tape directory
				can be rebuilt by reading all the
				data.

52	Tape system	C		The tape just unloaded could not		Write errors occurred while
	area write			write its system area successfully:		writing the system area on
	failure			1.	Copy the data to another tape	unload.
				1.	Copy the data to another tape
					cartridge.
				2.	Discard the old cartridge.

53	Tape system	C		The tape system area could not be		Read errors occurred while
	area read			read successfully at load time.		reading the system area on
	failure			Copy the data to another tape		load.
				Copy the data to another tape
				cartridge.

54	No start of data	C		The start of data could not be found		The tape has been
				on the tape:		damaged, bulk erased, or is
				1.	Check that you are using the	of an incorrect format.
				1.	Check that you are using the
					correct format tape.
				2.	Discard the tape or return the
					tape to your supplier.

55	Loading failure	C		The operation has failed because the		The drive is unable to load
				media cannot be loaded and		the cassette and thread the
				threaded.		tape.
				1.	Remove the cartridge, inspect it
					as specified in the product
					manual, and retry the operation.
				2.	If the problem persists, call the
					tape drive supplier’s help line.

56	Unrecoverable	C		The operation has failed because the		The drive is unable to
	load failure			tape cannot be unloaded:		unload the tape.
				1.	Do not attempt to extract the tape
					cartridge.
				2.	Call the tape driver supplier’s
					help line.

HP LTO Ultrium 4 drives technical reference manual, volume 2: software integration 85 HP restricted

Image 85

Contents LTO 4 FC, SCSI and SAS drives volume 2 software integrationHP LTO Ultrium tape drives technical reference manual HP restrictedLegal and notice information 1 Designing backup applications Contents2 Configuration and initialization 3 Use of tapes4 Factors affecting performance 5 Supporting Ultrium features7 Exception handling 6 Sense keys and codesHP restricted Documentation map Related documentsDocuments specific to HP Ultrium drives Drives-generalOperation Installation and configurationCartridges InterfaceDealing with errors Maintenance and troubleshootingGeneral documents and standardization LTO Ultrium featuresNon-immediate commands 1 Designing backup applicationsOptimizing performance Large data transfer sizeManaging the use of tapes Cleaning tape headsInformation in Cartridge Memory Monitoring tape useDiagnostic logs Design goals for LTO backup applicationsTapeAlert Displaying drive informationInclude the capability to download firmware Inquiry string recovery 2 Configuration and initializationOperating system drivers 16 Configuration and initialization ExampleSCSI protocol, regardless of transport or interface type Enabling additional LUN support Support for additional LUNSupporting additional LUNs 18 Configuration and initialization Using MODE SENSE Using Cartridge Memory attributes3 Use of tapes LTO cartridge memoryFinding the remaining capacity Tape status and capacityInterpreting Log Sense data Command descriptor block Using the SET CAPACITY commandCDB fields WORM media Changes to SCSI commandsHow WORM media works New additional sense codes and TapeAlert flagsERASE commands rejected Error Usage pageSET CAPACITY command Re-writing media labelsBehavior with a missing or inconsistent EOD value Using CM to check tape integrityUnique media identifier Load count Responding to Cartridge Memory dataBarcode support Corrective action RWW retry countsWays of optimizing performance 4 Factors affecting performanceDetecting the drive’s speed Ensuring the recommended minimum transfer sizesUsing the Performance Log page for diagnosing problems Using Cartridge Memory instead of tape headersTime-out values Media type identificationFactors affecting performance Recommended support of log pagesHost-related factors Recommendation Examplewhere possible or a reasonably sized RAID system. More disks means makes sense to split heavily used FC cards across separate PCI bussesDo not interleave write commands with other commands, such as READ Drive-related factorsFormat-related factors Page 34 Factors affecting performance Cartridge Memory LTO-CM 5 Supporting Ultrium featuresAutomation interface Further informationAutomation/Device Interface ADI Modes of usage through ACI Automation Control Interface ACISlave to a library controller ACI commands that affect drive streaming performance ACI command setSCSI pass-through mode Backward compatibility New features in ACISCSI command Encryption support Supporting the ACI protocol Further detailsRecommended ACI time-out values 42 Supporting Ultrium featuresTreatment of reserved fields Recommended power-up sequenceRecommended load-unload configuration Recommended Get Drive Status polling frequency Firmware upgrade via tapeACI protocol communications retry Upgrading the drive firmwareFirmware upgrade via ACI Firmware upgrade via the primary host interfaceLibrary firmware upgrade via tape Handling irregular cartridgesExpired cleaning cartridge HP-configured or Universal Cleaning cartridge HP-configured or UniversalNon-HP Ultrium 1 cleaning cartridge Unreadable data cartridgeData cartridge with unreadable CM Valid firmware upgrade cartridgeCartridge fails to seat or load Cartridge cannot be loadedCleaning Frequently asked questionsInvalid firmware upgrade cartridge Is there separate firmware for drives intended to go into libraries?Resetting drives Backup softwareResetting via the ACI Reset command Resetting using the ACIRSTL lineControlling data compression Accessing Cartridge Memory without threading the tapeOther mode page information Buffer size at EW-EOMWrite delay time Rewind on resetPartition size 52 Supporting Ultrium featuresSense keys-actions to take 6 Sense keys and codesAction Console MessageFor additional sense codes, see “3h-MEDIUM ERROR” on “3h-MEDIUM ERROR” on page 62 . Also see the Media Accesslog the error, terminate I/O to the drive, and pass the appropriate error to the calling applicationConsole Message ActionAction Console MessageAction Physical Additional sense codes-actions to takeEnd-of-Tape reached, unable to fit0h-NO SENSE 2h-NOT READY 1h-RECOVERED ERRORLUN not accessible, port in The software must issue a LOAD before media accessThe command cannot be executed because the specified 60 Sense keys and codesmechanism tests are being executed. When the tests are A READ , SPACE , WRITE or WRITE FILEMARKS command 3h-MEDIUM ERROR62 Sense keys and codes and the drive. Based on this, ask the user to clean the Send a console message that an unrecovered error on64 Sense keys and codes Send a message to the console indicating that there is 66 Sense keys and codes The current command such as READ, SPACE, REWIND4h-HW ERROR A MODE SELECT parameter list sent to the drive contains 5h-ILLEGAL REQUEST68 Sense keys and codes persistent reservation using the PERSISTENT RESERVE OUT 6h-UNIT ATTENTIONallowed to execute. In other words, some commands can 32 initiators to register, using PERSISTENT RESERVE OUTAction A PERSISTENT RESERVE OUT command was executed service action removed all reservations and the persistentWRITE BUFFER or MAINTENANCE OUT command A SET DEVICE IDENTIFIER command has been successful7h-DATA PROTECTION Action 8h-BLANK CHECK READ BUFFER command Bh-ABORTED COMMANDrelated to a missing EOD data set. The most likely cause A WRITE or WRITE FILEMARKS command has encountered Dh-VOLUME OVERFLOW76 Sense keys and codes 1. Retrieve fault information Typical escalation procedure3. Allow the user to try recovery 4. Allow the user to reset devicesSupporting TapeAlert Monitoring the condition of the drive and mediaType FlagsPage Page Page Page Page Page Page TapeAlert models Designing software to use the TapeAlert logTapeAlert polling usage model Reading the TapeAlert logTapeAlert informational exception usage model Responding to the ‘Clean’ LED One-Button Disaster Recovery OBDRSupporting OBDR Requirements for drivers and logical device managers Providing pass-through modeGlossary see ”read-while-write” Index Page Page HP restricted