HP 1920-16G, 1920-8G, 1920-48G Examining the installation site, Temperature/humidity, Cleanness

Page 6

The accessories shipped with the switch, including but not limited to power cables, are intended only for the switch. Please do not use them for other products.

Examining the installation site

The switches must be used indoors. You can mount your switch in a rack or on a workbench, but make sure:

A minimum clearance of 5 cm (1.97 in) is reserved at the air inlet and exhaust vents for ventilation.

The rack or workbench has a good ventilation system.

The rack or workbench is sturdy enough to support the switch and its accessories.

The rack or workbench is reliably grounded.

To ensure correct operation and long service life of your switch, install it in an environment that meets the requirements described in the following subsections.

Temperature/humidity

Maintain temperature and humidity in the equipment room as described in "Environmental specifications."

Lasting high relative humidity can cause poor insulation, electricity creepage, mechanical property change of materials, and metal corrosion.

Lasting low relative humidity can cause washer contraction and ESD and bring problems including loose captive screws and circuit failure.

High temperature can accelerate the aging of insulation materials and significantly lower the reliability and lifespan of the switch.

Cleanness

Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of metal components and contact points, especially when indoor relative humidity is low. In the worst case, electrostatic adsorption can cause communication failure.

Table 2 Dust concentration limit in the equipment room

Substance

Concentration limit (particles/m³)

Dust

≤ 3 x 104 (no visible dust on the tabletop over three days)

NOTE:

 

Dust diameter ≥ 5 μm

 

 

 

The equipment room must also meet strict limits on salts, acids, and sulfides to eliminate corrosion and premature aging of components, as shown in Table 3.

Table 3 Harmful gas limits in the equipment room

Gas

Maximum concentration (mg/m3)

SO2

0.2

H2S

0.006

 

 

 

2

Image 6
Contents HP 1920 Gigabit Ethernet Switch Series Page Contents Page Preparing for installation Safety recommendationsHP 1920 Gigabit Ethernet Switch Series models Cleanness Examining the installation siteTemperature/humidity Dust concentration limit in the equipment roomEMI Installing the switch Attaching Type-A mounting brackets to the switchAttaching Type-C mounting brackets to the switch Attaching Type-B mounting brackets to the rack post Mounting the switch on a workbench Mounting the switch on a wallHole spacing Connecting cables Connecting network cableInstalling the SFP transceiver module and optical fibers Connecting the console cable Connecting the AC power cordConnecting the DC power cord Power supply selection criteriaDC input voltage Power supply Verifying the installation Connecting the DC power cord to the DC power receptacleConnecting the console cable Accessing the switch for the first timeSetting up the configuration environment Console cableSetting terminal parameters Connection procedureSetting the serial port parameters Select File Properties in the HyperTerminal windowHyperTerminal window Powering on the switch Verification before power-onPowering on the switch Press Enter and the system displays the following prompt Support and other resources Contacting HPRelated information Conventions Convention DescriptionConvention Description Network topology icons 1920-8G Appendix a Chassis views and technical specificationsChassis views 1920-16G1920-24G 1920-48G1920-8G-PoE+ 65W 1920-8G-PoE+ 180W1920-24G-PoE+ 180W 1920-24G-PoE+ 370WChassis Dimensions H x W x D Maximum weight Physical specificationsChassis dimensions and weights Ports and interface card slotsEnvironmental specifications Power specificationsCooling system Chassis Fixed fansCopper port LEDs Power LEDAppendix B LEDs Fiber port LEDsRPS power LED description Only the HP 1920-24G-PoE+ 370W supports the RPSAppendix C Troubleshooting Troubleshooting methodsSymptom Troubleshooting method