United States Stove B2350B owner manual External Parts Diagram/List, Chimney Connection

Page 5

External Parts Diagram/List

CHIMNEY CONNECTION

Your smoke pipe should be assembled in such a way that the male section (crimped

17

1

12

14

13

3

2

18

11

15

10

164

6

5

6

7

9

8

9

Two basic types of chimneys are approved for use with solid fuel: Factory-built and ma- sonry. Factory-built chimney must comply with UL 103 type “HT” standard.

Do not expect your stove or furnace to create draft. Draft is not a function of the appliance. It is purely a function of the chimney. Modern stoves and furnaces are much more air-tight and efficient than those of the past and, therefore re- quire greater draft. A minimum of .05 w.c. (12.45Pa), is required for proper drafting to prevent back-puffing, smoke spillage, and to maximize performance. Gauges to measure chimney draft are readily avail- able at stove shops and are economical to purchase or rent.

Chimneys perform two functions - one of which is apparent: The chimney provides a means for exhausting smoke and flue gases resulting from combustion of the fuel. Secondarily, though, the chimney provides “Draft” which allows oxygen to be continu- ously introduced into the appliance, so that proper combustion is possible.

IMPORTANT

end) of the pipe faces down. This will allow condensation in the flue to run back into the heater. Attach each of the sections to one another with three equidistant metal screws and seal each joint with furnace cement.

The pipe must be short and straight. All sections installed horizontally must slope at least 1/4 inch per foot, with the upper end of the section toward the chimney.

To insure a good draft, the total length of the coupling pipe should never exceed 8’ to 10’ (2.4m to 3.04 m). (Except for cases of vertical installation, cathedral-roof style where the smoke exhaust system can be much longer and connected without problem to the chimney at the ceiling of the room).

It is recommended that no more than two 90 degree bends be used because it may reduce the amount of natural draft. The use of corrugated (non-adjustable) elbows is preferred as they are much more airtight.

You must have at least 18 inches of clearance between any horizontal piping and the ceiling.

The pipe cannot extend into the chimney

Key

Part No.

Description

Qty.

 

 

 

 

1

67725P

Panel, Cabinet Front - Pewter

1

2

23477

Shield, Top Thermo

1

3

67967B

Cabinet, Left

1

4

67968B

Frame, Door

1

5

67969B

Door, Cabinet

1

Your chimney connector and chimney must have the same diameter as the stove outlet (6”). If this is not the case, we recommend you contact your dealer in order to insure there will be no problem with the draft.

The stove pipe must be made of aluminized or cold roll steel with a minimum thickness of 0.021” or 0.53 mm. It is strictly forbidden to use galvanized steel.

flue.

The chimney connector must not pass through an attic, roof space, closet, any concealed space, floor, ceiling, wall or combustible construction. Where passage through a wall or partition of combustible construction, the installation must conform to CAN/CSA-B365, Installation Code for Solid-Fuel-Burning Appliances & Equipment.

6

89065

Hinge, Door

4

7

89635

Knob, Door

1

8

83093

Latch, Spring

1

9

83005

#10-24 x 1/2 Machine Screw, PH HD

2

10

69557B

Back, Cabinet

1

11

21063

Brace, Back

2

12

67966B

Top, Cabinet

1

13

21593

Support, Hinge

1

14

83833

Clip, Hinge

1

15

67743

Assy., Thermostat

1

16

69271

Chain & Hook Assembly

1

17

851886

Plate, Control Panel - Wonderluxe

1

18

89687

Knob, Thermostat

1

 

 

20

 

To Stove

5

Image 5
Contents United States Stove Company WonderluxeCirculator dimensions Warranty Information CardRules for safe installation and operation Tools and Materials NeededMinimum clearances to combustible walls and ceilings HOW to Order Repair PartsAS a Location is SELECTED, Keep the Following Mind Locating the HeaterChimney Connection External Parts Diagram/ListFlue Serving Another Appliance Parts ListChimney Factory Built Chimney Internal Parts DiagramDisposal of Ashes Venting into a fireplace MAINTENANCEMasonry Chimney Bulletine RC454DR6 6 Draft Regulator Optional kit B36TK Thermodisc kit for b36 blower OptionalSize of Coal Masonry Chimney Bulletine RC454Stove Operation Burning BituminousOperating Instructions Combustible Wall Chimney Connector Pass-ThroughsHOW to Open the TOP LID CB36 Room Blower Assembly