United States Stove B2045L, B2045N manual Troubleshooting, Observed Problem Possible Cause Remedy

Page 20

TROUBLESHOOTING

WARNING

Turn off and let cool before servicing. Only a qualified service person should service and repair heater.

NOTE: All troubleshooting items are listed in order of operation.

OBSERVED PROBLEM

POSSIBLE CAUSE

 

REMEDY

 

• Ignitor electrode positioned wrong

• Replace

ignitor.

 

• Ignitor electrode is broken

• Replace

ignitor.

 

• Ignitor electrode not connected to ignitor

• Reconnect ignitor cable.

When ignitor button is pressed, there is

cable.

 

 

 

 

 

no spark at ODS/Pilot.

• Ignitor cable pinched or wet keep ignitor

• Free ignitor cable if pinched by any metal

 

cable dry.

or tubing.

 

• Broken ignitor cable

• Replace ignitor cable.

 

• Bad piezo ignitor

• Replace piezo ignitor.

 

 

 

 

• Appliance burning vapors from paint, hair

• Ventilate room. Stop using odor-causing

Appliance produces unwanted odors.

spray, glues, etc.

products while heater is running.

 

• Gas leak.

• Locate and correct all leaks.

 

 

 

 

 

• Not enough fresh air is available for ODS/

• Open window and/or door ventilation

 

Pilot to operate.

 

 

 

Appliance shuts off in use.

• Low line pressure.

• Contact local gas company.

 

 

 

 

 

• ODS/Pilot is partially clogged.

• Clean ODS/Pilot.

 

 

 

Gas odor even when control knob is in

• Gas leak.

• Locate and correct all leaks.

OFF position.

• Control valve defective.

• Replace control valve.

 

 

 

 

 

• Gas supply turned off or manual shutoff

• Turn on gas supply or open manual shutoff

 

valve.

 

 

valve closed.

 

 

• Turn control knob while in PILOT position.

 

 

When ignitor button is pressed, there is

• Control knob not in PILOT position.

• Press in control knob while in PILOT posi

 

tion.

 

spark at ODS/Pilot, but no ignition.

 

 

• Control knob not pressed in while in Pilot

• Continue holding down control knob.

 

 

position

Repeat igniting operation until air is re-

 

• Air in gas lines when installed.

moved

 

 

• Replace ODS/pilot assembly or get is ser-

 

 

 

 

viced.

 

 

 

• Replace gas regulator.

 

 

 

 

• Control knob not fully pressed in.

• Press in control knob fully.

 

 

 

ODS/Pilot lights, but flame goes out

• Control knob not pressed in long enough.

• After ODS/pilot lights, keep control knob

when control knob is released.

pressed in 30 seconds.

 

 

• Manual shutoff valve not fully open.

• Fully open manual shutoff valve.

20

Image 20
Contents Fuego Table of Contents Important Safety Information Product Features FeaturesSpecifications ContentsCodes Items Required for InstallationItems Required for Installation Installation Mantel Clearances GAS Connection Gas ConnectionGAS Pressure Check Rear View of 2045 Vent-Free Gas HeaterLOG Assembly Proper Installation SequenceRemoving Front Screen LOG PositioningFor Your Safety Read Before Lighting For Your SafetyOperating Instructions What to do if YOU Smell GASLighting Instructions Turn OFF GAS to ApplianceCleaning / Servicing Match Lighting InstructionsChecking Flame Appearance Pilot FlameFlame Appearance FlamesHeater Assembly Replacement Parts Parts List for Heater Assembly KEY Description QTYBurner & LOG Assembly Parts List for Generator and LOG Assembly Troubleshooting Observed Problem Possible Cause RemedyTroubleshooting Optional Kits for the B2045 Wiring Diagram for Generator Assembly Optional Kits for the B2045Standard Wiring from Factory Wiring with the WSK60 Wall Switch KIT Page Limited Warranty Policy HOW to Order Repair Parts or Options United States Stove Company