BENDIX SD-05-1269 manual Initial Installation Preparation, Slack Adjuster Arm Length Angle

Page 4

INITIAL INSTALLATION PREPARATION

1.If necessary, carefully remove the manual or automatic slack adjuster currently installed, including the brake chamber yoke assembly.

2.Before mounting the ASA-5®slack adjuster on the camshaft, check the brake chamber push rod length to determine whether shortening or replacement is required. To accomplish this:

A.With the brake chamber in the released position, place a square (or equivalent object) so that one edge is parallel to the actuator push rod while the other edge bisects the brake camshaft. Measure the distance from the push rod end to the vertical edge of the square and compare it to the values in Figure 5.

B.If the measurement is less than the minimum shown in Figure 5, the brake actuator push rod must be shortened. If the measurement is greater than the maximum values, the brake actuator push rod may require replacement. The extended adapter, available as a separate service part (5/8"-18 pc. no. 297700 and 1/2"-20 pc. no. 297701) may avoid the need to replace the brake actuator push rod. The extended adapter is available for the easy-on yoke assembly only. Note: Installing any other type of push rod extender is not recommended, because these devices may loosen over time and result in an improperly adjusted brake.

BRAKE ACTUATOR

PUSH ROD

SQUARE

 

 

 

DISTANCE

 

 

 

"A"

MOUNTING

 

 

STUD

 

 

 

 

 

SLACK

 

"A" STD.

"A"

 

 

 

 

ADJUSTER

 

QUICK CONNECT

EXTENDED

ARM

 

OR EASY-ON

EASY-ON

LENGTH

 

ADAPTER

ADAPTER

5"

 

1-15/16" - 3-1/32"

2-7/16" - 3-17/32"

5-1/2"

 

1-15/16" - 3-3/16"

2-7/16" - 3 11/16"

 

 

 

 

6"

 

1-3/16" - 3-3/16"

1-11/16" - 3-11/16"

 

 

 

 

FIGURE 5 - MEASURING THE BRAKE ACTUATOR PUSH

ROD

3.Inspect the foundation brake, brake chamber and related components. Make certain the camshaft bushings and seals are not excessively worn. Lubricate the camshaft bushings. Check the brake chamber bracket for cracks and excessive corrosion. The brake actuator push rod should not be loose or bent and the return spring should be fi rm. Replace parts that are suspect.

4.Wire brush the foundation brake camshaft to loosen contamination and wipe clean. Depending on environmental conditions, an application of anti-seize compound to both the camshaft and worm gear spline may facilitate later slack removal.

INSTALLATION

1.Select the proper ASA-5®slack adjuster.

2.Install the ASA-5®slack adjuster on the brake camshaft.

3.If the ASA-5®slack adjuster has the easy-on yoke (see Figure 3), position the brake actuator push rod jam nut approximately 1-5/16 inches from the end of the brake actuator push rod. Thread the easy-on yoke adapter on the brake actuator push rod until it is approximately 3/8 inch from the end of the brake actuator push rod end. Turn the ASA-5®slack adjuster manual adjustment hex clockwise until the adapter extends into the threaded bore of the yoke approximately 1/8 inch. Thread the adapter into the yoke and tighten to 10 foot pounds.

The installation angle of a properly installed ASA-5®slack adjuster:

4.If the ASA-5®slack adjuster has the quick connect yoke (see Figure 4), position the brake actuator push rod jam nut approximately 1 inch from the end of the brake actuator push rod. Thread the quick connect adapter bushing on the brake actuator push rod until it is fl ush

FIGURE 6 - INSTALLATION ANGLE

Slack Adjuster

Arm Length

Angle

 

 

5"

99°-113°

 

 

5.5"

98°-111°

 

 

6"

90°-109°

 

 

4

Image 4
Contents Description OperationGeneral Brake ApplicationYoke Designs Brake ReleaseEASY-ON Yoke Refer to Figure QUICK-CONNECT Yoke Initial Installation Preparation InstallationSlack Adjuster Arm Length Angle Preventive Maintenance Service InspectionActuator Stroke Table Standard Stroke Long StrokeTesting the ASA-5ADJUSTER Mechanism Testing Adjuster MechanismBrake Maintenance Inspection DisassemblyASA-5SLACK Adjuster Removal Retrofitting the ASA-5SLACK Adjuster Cleaning and InspectionReassembly PreparationSlack adjusters should Adjusted in an effortIndicates that a Problem exists with Automatic adjusterASA-5SLACK Adjuster Troubleshooting Chart