ASRock A75 Pro4/MVP manual Installing a Dimm, Notch break Break

Page 18

Installing a DIMM

Please make sure to disconnect power supply before adding or removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

notch break

notch

break

The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated.

18

Image 18
Contents A75 Pro4/MVP Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Rear Panel I/O ConnectorAudio USBUnique Feature Smart SwitchBios Feature Support CDPage Page Page Motherboard Layout DDR3I/O Panel LAN Port LED IndicationsTable for Audio Output Connection Page Installation Pre-installation PrecautionsCPU Installation Installation of CPU Fan and HeatsinkInstallation of Memory Modules Dimm Dual Channel Memory ConfigurationsInstalling a Dimm Notch break BreakInstalling an expansion card Expansion Slots PCI and PCI Express SlotsPcie Slots Graphics Card Setup CrossFireXTM and Quad CrossFireXTM Operation GuideCrossFire Bridge Driver Installation and Setup For Windows XP OSFor Windows 7 / VistaTM OS Page AMD Dual Graphics Operation Guide Enjoy the benefit of AMD Dual GraphicsWhat does an AMD Dual Graphics system include? AMD Vision Engine Control Center Dual Monitor and Surround Display Features Dual Monitor FeatureSurround Display Feature For Windows XP / XP 64-bit OSWhat is HDCP? For Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OSHdcp Function ASRock Smart Remote Installation Guide CIR sensors in different anglesJumpers Setup DescriptionOnboard Headers and Connectors Serial ATA3 ConnectorsInfrared Module Header Chassis Speaker Header CPU Fan Connectors ATX 12V Power ConnectorSerial port Header Smart Switches 12 Dr. Debug Status Code DescriptionPage Page Page What is Hot Swap Function? Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug Function? Hot Plug and Hot Swap Functions for SATA3 HDDsSATA3 HDD Hot Plug Feature and Operation Guide Points of attention, before you process the Hot PlugHow to Hot Plug a SATA3 HDD Driver Installation Guide Installing Windows XP / XP 64-bit With RAID FunctionsSet up Uefi Use RAID Installation Guide to set RAID configuration \ RAID Installation Guide Make a SATA3 Driver DisketteInstalling Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar Navigation Keys + / Tab Enter Pgup Pgdn Home Navigation KeysMain Screen F10 F12OC Tweaker Screen RAS# to CAS# Delay tRCD Dram Configuration Dram FrequencyDram Timing Control Power Down Enable CPU VoltageRAS to RAS Delay tRRD Command Rate CRWrite Recovery Time tWR Write to Read Delay tWTRAdvanced Screen Instant FlashCstate Pmin Mode CPU ConfigurationCore C6 Mode Cool ‘n’ QuietNorth Bridge Configuration South Bridge Configuration Sata IDE Combined Mode Storage ConfigurationSata Mode Sata ControllerSerial Port Address Super IO ConfigurationSerial Port Infrared PortAcpi Configuration Acpi Hpet table A75 USB 3.0 Controller USB ConfigurationUSB 2.0 Controller Legacy USB SupportChassis Fan 2 Setting CPU Fan 1 & 2 SettingChassis Fan 1 Setting Chassis Fan 3 SettingBoot Screen Security Screen Save Changes and Exit Load Uefi DefaultsExit Screen Discard Changes and ExitRunning The Support CD Install Operating SystemSupport CD Information Drivers MenuInstalling OS on a HDD Larger Than 2TB
Related manuals
Manual 200 pages 7.32 Kb