ASRock A75 Pro4/MVP manual

Page 47

2.18.2 Installing Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit Without RAID Functions

If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit on your SATA3 HDDs without RAID functions, please follow below steps.

Using SATA3 HDDs with NCQ and Hot Plug functions (AHCI mode) STEP 1: Set up UEFI.

A.Enter UEFI SETUP UTILITY Advanced screen Storage Configuration.

B.Set the “SATA Mode” option to [AHCI].

STEP 2: Install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system.

Using SATA3 HDDs without NCQ and Hot Plug functions (IDE mode) STEP 1: Set up UEFI.

A.Enter UEFI SETUP UTILITY Advanced screen Storage Configuration.

B.Set the “SATA Mode” option to [IDE].

STEP 2: Install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system.

47

Image 47

Contents A75 Pro4/MVP Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications USB ConnectorAudio Rear Panel I/OSupport CD Smart SwitchBios Feature Unique FeaturePage Page Page DDR3 Motherboard LayoutTable for Audio Output Connection I/O PanelLAN Port LED Indications Page Pre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationDual Channel Memory Configurations Installation of Memory Modules DimmNotch break Break Installing a DimmPcie Slots Installing an expansion cardExpansion Slots PCI and PCI Express Slots CrossFireXTM and Quad CrossFireXTM Operation Guide Graphics Card SetupCrossFire Bridge For Windows 7 / VistaTM OS Driver Installation and SetupFor Windows XP OS Page What does an AMD Dual Graphics system include? AMD Dual Graphics Operation GuideEnjoy the benefit of AMD Dual Graphics AMD Vision Engine Control Center Dual Monitor Feature Dual Monitor and Surround Display FeaturesFor Windows XP / XP 64-bit OS Surround Display FeatureHdcp Function What is HDCP?For Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS CIR sensors in different angles ASRock Smart Remote Installation GuideDescription Jumpers SetupSerial ATA3 Connectors Onboard Headers and ConnectorsInfrared Module Header Chassis Speaker Header ATX 12V Power Connector CPU Fan ConnectorsSerial port Header Smart Switches Status Code Description 12 Dr. DebugPage Page Page Hot Plug and Hot Swap Functions for SATA3 HDDs Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug Function? What is Hot Swap Function?Points of attention, before you process the Hot Plug SATA3 HDD Hot Plug Feature and Operation GuideHow to Hot Plug a SATA3 HDD Set up Uefi Driver Installation GuideInstalling Windows XP / XP 64-bit With RAID Functions \ RAID Installation Guide Make a SATA3 Driver Diskette Use RAID Installation Guide to set RAID configurationInstalling Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar F10 F12 Navigation KeysMain Screen Navigation Keys + / Tab Enter Pgup Pgdn HomeOC Tweaker Screen CPU Voltage Dram Configuration Dram FrequencyDram Timing Control Power Down Enable RAS# to CAS# Delay tRCDWrite to Read Delay tWTR Command Rate CRWrite Recovery Time tWR RAS to RAS Delay tRRDInstant Flash Advanced ScreenCool ‘n’ Quiet CPU ConfigurationCore C6 Mode Cstate Pmin ModeNorth Bridge Configuration South Bridge Configuration Sata Controller Storage ConfigurationSata Mode Sata IDE Combined ModeInfrared Port Super IO ConfigurationSerial Port Serial Port AddressAcpi Configuration Acpi Hpet table Legacy USB Support USB ConfigurationUSB 2.0 Controller A75 USB 3.0 ControllerChassis Fan 3 Setting CPU Fan 1 & 2 SettingChassis Fan 1 Setting Chassis Fan 2 SettingBoot Screen Security Screen Discard Changes and Exit Load Uefi DefaultsExit Screen Save Changes and ExitDrivers Menu Install Operating SystemSupport CD Information Running The Support CDInstalling OS on a HDD Larger Than 2TB

Related manuals

Manual 200 pages 7.32 Kb