ASRock A75 Pro4/MVP manual Uefi Menu Bar

Page 48

3. UEFI SETUP UTILITY

3.1 Introduction

This section explains how to use the UEFI SETUP UTILITY to configure your sys- tem. The SPI Memory on the motherboard stores the UEFI SETUP UTILITY. You may run the UEFI SETUP UTILITY when you start up the computer. Please press <F2> or <Del> during the Power-On-Self-Test (POST) to enter the UEFI SETUP UTILITY, otherwise, POST will continue with its test routines.

If you wish to enter the UEFI SETUP UTILITY after POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You may also restart by turning the system off and then back on.

Because the UEFI software is constantly being updated, the following UEFI setup screens and descriptions are for reference purpose only, and they may not exactly match what you see on your screen.

3.1.1 UEFI Menu Bar

The top of the screen has a menu bar with the following selections:

Main

To set up the system time/date information

OC Tweaker

To set up overclocking features

Advanced

To set up the advanced UEFI features

H/W Monitor

To display current hardware status

Boot

To set up the default system device to locate and load the

 

Operating System

Security

To set up the security features

Exit

To exit the current screen or the UEFI SETUP UTILITY

Use < > key or < > key to choose among the selections on the menu bar, and then press <Enter> to get into the sub screen.

48

Image 48
Contents A75 Pro4/MVP Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Connector AudioRear Panel I/O USBSmart Switch Bios FeatureUnique Feature Support CDPage Page Page Motherboard Layout DDR3I/O Panel LAN Port LED IndicationsTable for Audio Output Connection Page Installation Pre-installation PrecautionsCPU Installation Installation of CPU Fan and HeatsinkInstallation of Memory Modules Dimm Dual Channel Memory ConfigurationsInstalling a Dimm Notch break BreakInstalling an expansion card Expansion Slots PCI and PCI Express SlotsPcie Slots Graphics Card Setup CrossFireXTM and Quad CrossFireXTM Operation GuideCrossFire Bridge Driver Installation and Setup For Windows XP OSFor Windows 7 / VistaTM OS Page AMD Dual Graphics Operation Guide Enjoy the benefit of AMD Dual GraphicsWhat does an AMD Dual Graphics system include? AMD Vision Engine Control Center Dual Monitor and Surround Display Features Dual Monitor FeatureSurround Display Feature For Windows XP / XP 64-bit OSWhat is HDCP? For Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OSHdcp Function ASRock Smart Remote Installation Guide CIR sensors in different anglesJumpers Setup DescriptionOnboard Headers and Connectors Serial ATA3 ConnectorsInfrared Module Header Chassis Speaker Header CPU Fan Connectors ATX 12V Power ConnectorSerial port Header Smart Switches 12 Dr. Debug Status Code DescriptionPage Page Page Serial ATA3 SATA3 Hard Disks Installation What is Hot Plug Function?What is Hot Swap Function? Hot Plug and Hot Swap Functions for SATA3 HDDsSATA3 HDD Hot Plug Feature and Operation Guide Points of attention, before you process the Hot PlugHow to Hot Plug a SATA3 HDD Driver Installation Guide Installing Windows XP / XP 64-bit With RAID FunctionsSet up Uefi Use RAID Installation Guide to set RAID configuration \ RAID Installation Guide Make a SATA3 Driver DisketteInstalling Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar Navigation Keys Main ScreenNavigation Keys + / Tab Enter Pgup Pgdn Home F10 F12OC Tweaker Screen Dram Configuration Dram Frequency Dram Timing Control Power Down EnableRAS# to CAS# Delay tRCD CPU VoltageCommand Rate CR Write Recovery Time tWRRAS to RAS Delay tRRD Write to Read Delay tWTRAdvanced Screen Instant FlashCPU Configuration Core C6 ModeCstate Pmin Mode Cool ‘n’ QuietNorth Bridge Configuration South Bridge Configuration Storage Configuration Sata ModeSata IDE Combined Mode Sata ControllerSuper IO Configuration Serial PortSerial Port Address Infrared PortAcpi Configuration Acpi Hpet table USB Configuration USB 2.0 ControllerA75 USB 3.0 Controller Legacy USB SupportCPU Fan 1 & 2 Setting Chassis Fan 1 SettingChassis Fan 2 Setting Chassis Fan 3 SettingBoot Screen Security Screen Load Uefi Defaults Exit ScreenSave Changes and Exit Discard Changes and ExitInstall Operating System Support CD InformationRunning The Support CD Drivers MenuInstalling OS on a HDD Larger Than 2TB
Related manuals
Manual 200 pages 7.32 Kb