Alcatel IPTOUCH 300 manual Batteries and chargers, Gang Charger only on Mobile IPTouch

Page 23

Batteries and chargers

„Indicator light.

When the handset or Battery Pack is seated correctly, the corresponding indicator light will come on. A bright indicator means the Battery Pack is charging, a dim indicator means the Battery Pack is waiting to charge. The indicator light will not come on when the handset is incorrectly seated, the slot is empty or when the Dual Charger has no power applied. If the indicator light is off or flashing, it means the handset or Battery Pack is incorrectly seated. Remove the handset or Battery Pack and reinsert. If the LED continues to blink or starts blinking at any time during the charging process, it indicates that there is a problem with the Battery Pack that makes it unusable. Do not continue to charge the Battery Pack. Dispose of it properly and do not attempt to use it in the MIPT. Do not attempt to open or repair a defective Battery Pack. Contact your service representative for assistance.

The indicator light will turn off when charging is complete. Full charging is accomplished in approximately two hours for either slot.

„Charging indicator.

While the MIPT is charging in standby mode, it will display its extension number and Charging... The battery icon will show charging progress. The handset is fully operational and will ring if called. When the MIPT is charging while turned off, only Charging will display and no calls will be received.

„Charge Complete.

When the MIPT is fully charged, Charge Complete will display. If the MIPT has been turned off, the charge complete melody will play when it is turned on.

6.4 The Gang Charger - only on Mobile IPTouch 600

The Gang Charger is designed to charge four Nickel Metal Hydride (NiMH) Battery Packs simultaneously. Full charging is accomplished in approximately one and a half hours. Chargers operate in a 50° to 85° F (10° to 30° C) environment. Do not expose them to freezing temperatures or direct sunlight.

The Gang Charger is shipped with the appropriate power supply for the sites location. Place the Gang Charger on a flat, horizontal surface. Plug the power supply into the Gang Charger and into an appropriate wall outlet.

„Using the GC

Insert the Battery Pack into one of the four charging bays so that the Battery Pack contacts meet the charging bay contacts. The LED above the charging bay will turn on to indicate that charging is in progress. Complete charging occurs in one and a half to two hours. The Battery Pack is partially charged in five minutes. When charging is complete the LED will turn off. Lift the Battery Pack out of the charging bay.

„Blinking LED

If the LED starts blinking as soon as the Battery Pack is inserted, the Battery Pack may be improperly seated. Lift it out and reinsert. If the LED continues to blink or starts blinking at any time during the charging process, it indicates that there is a problem with the Battery Pack that makes it unusable. Do not continue to charge the Battery Pack. Dispose of it properly and do not attempt to use it in the MIPT. Do not attempt to open or repair a defective Battery Pack. Contact your service representative for assistance.

6.5

Cleaning the Chargers

Clean the Chargers by wiping the surface with a clean, water-dampened cloth or paper towel. A mild detergent solution may be used. Be sure to wipe away any detergent residue with a plain water dampened cloth. DO NOT IMMERSE THE CHARGER IN WATER OR OTHER LIQUID. DO NOT POUR LIQUIDS INTO THE SLOT.

The Battery Pack contacts on the MIPT may be cleaned with isopropyl (rubbing) alcohol applied with a Q-tip, cloth, or paper towel. Do not push or pull the exposed Battery Pack contacts.

Important information

Never use non-MIPT charging units as they could damage the Battery Pack.

Only use the original plug-in power adapter for the Chargers.

Do not immerse the Battery Pack in water or throw into the fire.

Do not throw away the Battery Pack with your domestic waste. Take used Battery Packs to an appropriate collection point for recycling or send them back to your supplier or servicing agent.

Replacement Battery Packs are available from your supplier or servicing agent.

23

Image 23
Contents Mobile IPTouch 300/600 Page Introduction How to use this guidePage Contents Getting to know your telephone Using your telephone Mute, so that your correspondent cannot hear you Using your telephoneSending Dtmf signals Make a call-back request to a busy numberMaking a second call during a conversation Switching between calls Broker callDuring a conversation Transferring a callBarring the reception of a new call during communication During a conversationConference Enter Number Intrusion into an internal conversationProtection against intrusion TwiceHunting groups 3SharingAnswering the general bell Call pick-upCalling a correspondent on his/her loudspeaker SharingSending a written message to an internal correspondent Answering a call on your pagerEnter Destination Voicemail number Send messageDuring the recording, you can End of recordingDiverting calls to another number immediate diversion When you return, consult recorded messagesDiverting your calls to your voice message service Keep in touchDo not disturb Cancelling all diversionsDiverting calls when your line is busy divert if busy Keep in touchDelete the message Consulting written messagesDisplay name of sender, with Date, time and ranking MessageNumber required Managing your chargesCharging your calls directly to business accounts Programming your telephone Lock / unlock your telephone Programming your telephoneLock the keypad automatically Activate/deactivate the Warning tonesActivate/deactivate the Key tones Locking the keypadDual Chargers Batteries and chargersBatteries Desktop ChargerImportant information Cleaning the ChargersBatteries and chargers Gang Charger only on Mobile IPTouchPush to Talk Mobile IP Touch Only Guarantee and clauses