ASRock Fatal1ty X79 Professional manual Driver Installation Guide, Set up Uefi

Page 56

2.21 Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical drive ﬁrst. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you install can work properly.

2.22Installing Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit With RAID Functions

RAID mode is not supported under Windows® XP / XP 64-bit.

If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on Intel® SATA2 / SATA3 ports with RAID functions, please follow below steps.

STEP 1: Set up UEFI.

A. Enter UEFI SETUP UTILITY Advanced screen Storage Conﬁguration. B. Set the option “SATA Mode” to [RAID] for Intel® SATA2 / SATA3 ports.

Set the option “Bootable Marvell SATA3 Controller“ to [Yes] for Marvell SATA ports.

STEP 2: Use “RAID Installation Guide” to set RAID conﬁguration.

Before you start to conﬁgure the RAID function, you need to check the installation guide in the Support CD for proper conﬁguration. Please refer to the document in the Support CD, “Guide to SATA Hard Disks Installation and RAID Conﬁguration”, which is located in the folder at the following path:

.. \ RAID Installation Guide

STEP 3: Install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system. The optical drive should be installed on an non Intel® SATA2 / SATA3 port.

Insert the Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit optical disk into the optical drive to boot your system, and follow the instruction to install OS on your system. When you see “Where do you want to install Windows?” page, please insert our Support CD to your system, and click the “Load Driver” button to load Intel® RAID drivers. Intel® RAID drivers are located in the following path of our Support CD:

32 bit: ..\i386\Win7_Vista_Intel_v3.0.0.1112

64-bit: ..\AMD64\Win7-64_Vista64_Intel_v3.0.0.1112

After that, please insert Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit optical disk into the optical drive again to continue the OS installation.

56

Image 56

Contents Fatal1ty X79 Professional Series Fatal1ty Story LIVIN’ Large Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications USB3.0 ConnectorSmart Switch Bios Feature Unique FeatureSupport CD HardwarePage Page Page Motherboard Layout 24.4cm 9.6LAN Port LED Indications Table for Audio Output ConnectionPage Pre-installation Precautions Screw HolesCPU Installation Locate Pin1 and the two orientation key notches Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Installing a DimmExpansion Slots PCI and PCI Express Slots Pcie Slot ConﬁgurationsInstalling an expansion card Requirements ASRock SLIBridge3S Card Installing Three SLITM-Ready Graphics Cards Two GoldﬁngersInstalling Four SLITM-Ready Graphics Cards Driver Installation and Setup For Windows XP / XP 64-bit OS For Slitm mode onlySelect Nvidia Control Panel tab Follow steps a to E on Page CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards Installing Four CrossFireXTM-Ready Graphics Cards For Windows XP OS For Windows 7 / VistaTM OSSurround Display Feature \ Surround Display InformationASRock Smart Remote Installation Guide CIR sensors in different anglesASRock XFast Charger Operation Guide Jumpers Setup DescriptionOnboard Headers and Connectors Serial ATA3 ConnectorsUSB 2.0 Headers Besides six default USB Consumer Infrared Module Header This header can be used to Chassis Speaker Header Please connect the chassis CPU Fan Connectors Please connect the CPU fan Port on the I/O panel, there Installation Guide of Front USB 3.0 Panel Installation Guide of Rear USB 3.0 BracketSmart Switches 15 Dr. Debug Status Code DescriptionPage Page Page Serial ATA Sata / Serial ATA2 SATA2 Hard Disks Installation Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug Function? What is Hot Swap Function?Hot Plug and Hot Swap Functions for Sata / SATA2 HDDs Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug How to Hot Plug a Sata / SATA2 / SATA3 HDD Use RAID Installation Guide to set RAID conﬁguration Driver Installation GuideSet up Uefi Installing Windows XP / XP 64-bit Without RAID Functions Install Windows XP / XP 64-bit OS on your systemUntied Overclocking Technology Introduction Uefi Menu BarNavigation Keys Main ScreenTo jump to the Exit Screen or exit the current screen System BrowserOC Tweaker Screen Turbo Boost Power Limit Dram Timing Control Load XMP SettingCore Current Limit Additional Turbo VoltageCommand Rate Dram Power Down ModeDram tRP Dram tRASMemory Power Savings Mode Memory ModeChannel Interleaving Rank InterleavingLoad Power Saving Mode User DefaultsCPU PLL Voltage PCH 1.1V VoltageAdvanced Screen Instant FlashCPU Configuration CPU Thermal Throttling Enhance Halt State C1ECPU C3 State Support CPU C6 State SupportNorth Bridge Configuration South Bridge Configuration Good Night LED Onboard Debug Port LEDStorage Configuration Hard Disk S.M.A.R.T Super IO Configuration Serial PortSerial Port Address Infrared PortAcpi Configuration USB Configuration ME Subsystem Intel ME Subsystem Conﬁguration ME VersionHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Software Support Installing OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Windows VistaTM 64-bit Page Windows 7 64-bit

Related manuals

Manual 238 pages 15.58 Kb