ASRock Fatal1ty X79 Professional manual Windows 7 64-bit

Page 87

c. Set “Startup type” to “Disable” then Click “OK”.

C. Reboot your system.

D. After reboot, please start to install motherboard drivers and utilities.

Windows® 7 64-bit:

A. Please request the hotfix KB2505454 through this link: http://support.microsoft.com/kb/2505454/

B. After installing Windows® 7 64-bit, install the hotfix kb2505454. (This may take a long time; >30 mins.)

C. Reboot your system. (It may take about 5 minutes to reboot.) D. Windows® will install this hotfix then reboot by itself.

E. Please start to install motherboard drivers and utilities.

6. Finish.

87

Image 87
Contents Fatal1ty X79 Professional Series Fatal1ty Story LIVIN’ Large Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Connector Smart SwitchUSB3.0 Hardware Bios FeatureUnique Feature Support CDPage Page Page 24.4cm 9.6 Motherboard LayoutTable for Audio Output Connection LAN Port LED IndicationsPage Screw Holes Pre-installation PrecautionsCPU Installation Locate Pin1 and the two orientation key notches Installation of CPU Fan and Heatsink Installing a Dimm Installation of Memory Modules DimmPcie Slot Configurations Expansion Slots PCI and PCI Express SlotsInstalling an expansion card Requirements ASRock SLIBridge3S Card Two Goldfingers Installing Three SLITM-Ready Graphics CardsInstalling Four SLITM-Ready Graphics Cards For Windows XP / XP 64-bit OS For Slitm mode only Driver Installation and SetupSelect Nvidia Control Panel tab Follow steps a to E on Page CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards Installing Four CrossFireXTM-Ready Graphics Cards For Windows 7 / VistaTM OS For Windows XP OS\ Surround Display Information Surround Display FeatureCIR sensors in different angles ASRock Smart Remote Installation GuideASRock XFast Charger Operation Guide Description Jumpers SetupSerial ATA3 Connectors Onboard Headers and ConnectorsUSB 2.0 Headers Besides six default USB Consumer Infrared Module Header This header can be used to Chassis Speaker Header Please connect the chassis CPU Fan Connectors Please connect the CPU fan Port on the I/O panel, there Installation Guide of Rear USB 3.0 Bracket Installation Guide of Front USB 3.0 PanelSmart Switches Status Code Description 15 Dr. DebugPage Page Page Serial ATA3 SATA3 Hard Disks Installation Serial ATA Sata / Serial ATA2 SATA2 Hard Disks InstallationHot Plug and Hot Swap Functions for SATA3 HDDs What is Hot Plug Function?What is Hot Swap Function? Hot Plug and Hot Swap Functions for Sata / SATA2 HDDsPoints of attention, before you process the Hot Plug How to Hot Plug a Sata / SATA2 / SATA3 HDD Driver Installation Guide Set up UefiUse RAID Installation Guide to set RAID configuration Install Windows XP / XP 64-bit OS on your system Installing Windows XP / XP 64-bit Without RAID FunctionsUntied Overclocking Technology Uefi Menu Bar IntroductionSystem Browser Navigation KeysMain Screen To jump to the Exit Screen or exit the current screenOC Tweaker Screen Additional Turbo Voltage Turbo Boost Power LimitDram Timing Control Load XMP Setting Core Current LimitDram tRAS Command RateDram Power Down Mode Dram tRPRank Interleaving Memory Power Savings ModeMemory Mode Channel InterleavingPCH 1.1V Voltage Load Power Saving ModeUser Defaults CPU PLL VoltageInstant Flash Advanced ScreenCPU Configuration CPU C6 State Support CPU Thermal ThrottlingEnhance Halt State C1E CPU C3 State SupportNorth Bridge Configuration South Bridge Configuration Onboard Debug Port LED Good Night LEDStorage Configuration Hard Disk S.M.A.R.T Infrared Port Super IO ConfigurationSerial Port Serial Port AddressAcpi Configuration USB Configuration Intel ME Subsystem Configuration ME Version ME SubsystemHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Software Support Installing OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Windows VistaTM 64-bit Page Windows 7 64-bit
Related manuals
Manual 238 pages 15.58 Kb