ASRock Fatal1ty X79 Professional manual Hardware Health Event Monitoring Screen

Page 78

3.5 Hardware Health Event Monitoring Screen

In this section, it allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, CPU fan speed, chassis fan speed, and the critical voltage.

CPU Fan 1 & 2 Setting

This allows you to set CPU fan 1 & 2’s speed. Configuration options: [Full On] and [Automatic Mode]. The default value is [Full On].

Chassis Fan 1 Setting

This allows you to set chassis fan 1’s speed. Configuration options: [Full On], [Automatic Mode] and [Manual]. The default value is [Full On].

Chassis Fan 2 Setting

This allows you to set chassis fan 2’s speed. Configuration options: [Level 1] to [Level 4]. The default value is [Level 4].

Chassis Fan 3 Setting

This allows you to set chassis fan 3’s speed. Configuration options: [Level 1] to [Level 4]. The default value is [Level 4].

Target Fan Speed

This allows you to set target fan speed. The default value is [Level 1].

Over Temperature Protection

Use this to enable or disable Over Temperature Protection. The default value is [Enabled].

78

Image 78
Contents Fatal1ty X79 Professional Series Fatal1ty Story LIVIN’ Large Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Connector Smart SwitchUSB3.0 Support CD Bios FeatureUnique Feature HardwarePage Page Page Motherboard Layout 24.4cm 9.6LAN Port LED Indications Table for Audio Output ConnectionPage Pre-installation Precautions Screw HolesCPU Installation Locate Pin1 and the two orientation key notches Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Installing a DimmExpansion Slots PCI and PCI Express Slots Pcie Slot ConfigurationsInstalling an expansion card Requirements ASRock SLIBridge3S Card Installing Three SLITM-Ready Graphics Cards Two GoldfingersInstalling Four SLITM-Ready Graphics Cards Driver Installation and Setup For Windows XP / XP 64-bit OS For Slitm mode onlySelect Nvidia Control Panel tab Follow steps a to E on Page CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards Installing Four CrossFireXTM-Ready Graphics Cards For Windows XP OS For Windows 7 / VistaTM OSSurround Display Feature \ Surround Display InformationASRock Smart Remote Installation Guide CIR sensors in different anglesASRock XFast Charger Operation Guide Jumpers Setup DescriptionOnboard Headers and Connectors Serial ATA3 ConnectorsUSB 2.0 Headers Besides six default USB Consumer Infrared Module Header This header can be used to Chassis Speaker Header Please connect the chassis CPU Fan Connectors Please connect the CPU fan Port on the I/O panel, there Installation Guide of Front USB 3.0 Panel Installation Guide of Rear USB 3.0 BracketSmart Switches 15 Dr. Debug Status Code DescriptionPage Page Page Serial ATA Sata / Serial ATA2 SATA2 Hard Disks Installation Serial ATA3 SATA3 Hard Disks InstallationHot Plug and Hot Swap Functions for Sata / SATA2 HDDs What is Hot Plug Function?What is Hot Swap Function? Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug How to Hot Plug a Sata / SATA2 / SATA3 HDD Driver Installation Guide Set up UefiUse RAID Installation Guide to set RAID configuration Installing Windows XP / XP 64-bit Without RAID Functions Install Windows XP / XP 64-bit OS on your systemUntied Overclocking Technology Introduction Uefi Menu BarTo jump to the Exit Screen or exit the current screen Navigation KeysMain Screen System BrowserOC Tweaker Screen Core Current Limit Turbo Boost Power LimitDram Timing Control Load XMP Setting Additional Turbo VoltageDram tRP Command RateDram Power Down Mode Dram tRASChannel Interleaving Memory Power Savings ModeMemory Mode Rank InterleavingCPU PLL Voltage Load Power Saving ModeUser Defaults PCH 1.1V VoltageAdvanced Screen Instant FlashCPU Configuration CPU C3 State Support CPU Thermal ThrottlingEnhance Halt State C1E CPU C6 State SupportNorth Bridge Configuration South Bridge Configuration Good Night LED Onboard Debug Port LEDStorage Configuration Hard Disk S.M.A.R.T Serial Port Address Super IO ConfigurationSerial Port Infrared PortAcpi Configuration USB Configuration ME Subsystem Intel ME Subsystem Configuration ME VersionHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Software Support Installing OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Windows VistaTM 64-bit Page Windows 7 64-bit
Related manuals
Manual 238 pages 15.58 Kb