ASRock ConRoe865PE manual Floppy Configuration, Super IO Configuration, OnBoard Floppy Controller

Page 32

3.3.6 Floppy Configuration

In this section, you may configure the type of your floppy drive.

 

BIOS SETUP UTILITY

 

 

Advanced

 

 

 

Floppy Configuration

 

Select the type of

 

 

floppy drive

Floppy A

[1.44 MB 312"]

connected to the

 

 

system.

 

 

 

Select Screen

 

 

 

Select Item

 

 

+-

Change Option

 

 

F1

General Help

 

 

F9

Load Defaults

 

 

F10

Save and Exit

 

 

ESC

Exit

v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.

3.3.7 Super IO Configuration

BIOS SETUP UTILITY

 

 

Advanced

 

 

 

Configure Super IO Chipset

 

Allow BIOS to Enable

 

 

or Disable Floppy

OnBoard Floppy Controller

[Enabled]

Controller.

 

 

Serial Port Address

[3F8 / IRQ4]

 

 

Infrared Port Address

[Disabled]

 

 

Parallel Port Address

[378]

 

 

Parallel Port Mode

[ECP + EPP]

 

 

EPP Version

[1.9]

 

 

ECP Mode DMA Channel

[DMA3]

 

 

Parallel Port IRQ

[IRQ7]

 

 

Onboard Game Port

[Enabled]

 

Select Screen

Onboard MIDI Port

[Disabled]

 

 

Select Item

 

 

 

 

 

+-

Change Option

 

 

F1

General Help

 

 

F9

Load Defaults

 

 

F10

Save and Exit

 

 

ESC

Exit

v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.

OnBoard Floppy Controller

Use this item to enable or disable floppy drive controller.

Serial Port Address

Use this item to set the address for the onboard serial port or disable it. Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4], [2E8 / IRQ3].

Infrared Port Address

Use this item to set the address for the onboard infrared port or disable it. Configuration options: [Disabled], [2F8 / IRQ3], and [2E8 / IRQ3].

3 2

Image 32
Contents ConRoe865PE Copyright Notice DisclaimerContents Software Support Package Contents IntroductionSpecifications Connector See Caution Bios FeatureSupport CD HardwarePage Motherboard Layout 22.9cm 9.0ASRock 8CH I/O Table for Audio Output ConnectionPre-installation Precautions Screw HolesCPU Installation Page Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Dual Channel Memory ConfigurationsInstalling a Dimm Notch breakInstalling an expansion card Expansion Slots PCI and AGP SlotsJumpers Setup Jumper Setting DescriptionOnboard Headers and Connectors IDE2USB 2.0 Header Chassis Speaker Header Untied Overclocking Technology Serial ATA Sata Hard Disks InstallationDriver Installation Guide Bios Menu Bar Advanced Screen Navigation KeysMain Screen CPU Configuration Boot Failure GuardCPU Host Frequency Spread SpectrumRatio Cmos Setting Ratio Actual ValueEnhance Halt State Max Cpuid Value LimitChipset Configuration Acpi Configuration IDE Configuration RTC Alarm Power OnOnBoard IDE Operate Mode Combined Mode OptionIDE Device Configuration LBA/Large ModePCIPnP Configuration Floppy Configuration Super IO ConfigurationOnBoard Floppy Controller Serial Port AddressParallel Port Mode ECP Mode DMA ChannelParallel Port Address EPP VersionUSB Configuration USB Controller EnabledUSB Controller USB 2.0 SupportTarget CPU Temperature C Hardware Health Event Monitoring ScreenCPU Quiet Fan Tolerance CBoot Screen Boot Settings ConfigurationBoot From Network Boot Up Num-LockBoot Device Priority 1st Boot Device 1st Floppy DriveMain Advanced Monitor Boot Change Supervisor PasswordLoad Optimal Defaults Exit ScreenSave Changes and Exit Discard Changes and ExitInstall Operating System LGA 775 CPU Installation Live Demo ProgramSupport CD Information Running The Support CD