MSI RG60G manual 1.6 L2TP

Page 22

MSI RG60G

6.Connection Control: There are 3 modes to select:

Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.

Auto-Reconnect(Always-on): The device will link up with ISP until the connection is established.

Manually: The device will not make the link until someone clicks the connect-button in the status-page.

4.3.1.6 L2TP

First check your ISP assigned and Select Static IP Address or Dynamic IP Address.

For example: Use Static

1.My IP Address and My Subnet Mask: the private IP address and subnet mask your ISP has assigned to you.

2.Server IP Address: the IP address of the PPTP server.

3.PPTP Account and Password: the account and password your ISP assigned to you. If you don't want to change the password, leave it blank.

16Turbo 802.11b/g 4 Port Wireless Broadband Router

Image 22

Contents MSI RG60G Italy Ieee 802.11b/g and Bluetooth 2.4 GHz operationIeee 802.11b/g und Bluetooth 2.4 GHz Betrieb LuxembourgHinweise zur Reichweite Operating rangeMSI Technology GmbH Revision History Date First Release July Important Safety Precautions Table of Content Functions and Features Roaming High speed for wireless LAN connectionStatistics of WAN Supported Ieee 802.11b compatible 11MDoS Attack Detection Supported SPI Mode SupportedSupport WPA-PSK and WPA System time SupportedPacking List Hardware Installation Panel LayoutAntenna LAN Ports 1~4 Power WAN Port Rear PanelSetup LAN connection Procedure for Hardware InstallationDecide where to place your Wireless Broadband Router Setup WAN connectionMake Correct Network Settings of Your Computer PingMSI RG60G Configuring Wireless Broadband Router Start-up and Log WizardSetup IP Setting WAN Type, IP Mode Press ChangeStatic IP Address Dynamic IP AddressPPP over Ethernet Pptp1.6 L2TP MSI RG60G Wireless Setting and 802.1X setting ＊ Wireless settings ＊ 802.1X Setting Radius Shared KeyWPA-PSK WPA2-PSK AES WPA2 AES WPA1/WPA2 3 WDS Dynamic DNS Dhcp Server Click More Advanced SPI Mode Basic Setting Discard Ping from WAN sideDoS Attack Detection MAC Address Control IP Address Packet Filtering ＊ Inbound Filter ExampleField MSI RG60G ＊ Log DNS Query ＊ Domain Filter EnableDomain Filtering ＊ Domain Filter ＊ Privilege IP Addresses Range＊ Enable ＊ URL Blocking Enable URL FilteringMSI RG60G Routing Table Destination Subnet Mask Gateway Hop Enabled Schedule Rule Click Add New RuleEdit After configure Rule 1à Schedule EnableDelete MSI RG60G Virtual Server 9 DMZ ＊ IP Address of DMZ Host ＊ Non-standard FTP portSpecial AP Change Password AdministrationRecommended Firmware Upgrade Backup SettingReboot Reset to factory defaultSystem Time ＊ Time Server Remote Access ＊ Remote Administrator Host/Port＊ Get Date and Time by NTP Protocol ＊ Time Zone＊ Administrator Time-out Network wake-up ＊ MAC Address for Wake-on-LANDiagnostic StatusSystem Status System Log＊ IP Address for Syslog ＊ E-mail Alert EnableLog Notification ＊ Smtp Server IP and Port＊ Get Community Snmp Setting＊ Enable Snmp ＊ Set CommunityConfiguring Turbo Mode With Client Select Optimize for performance mode Configuration Confirmation Appendix a TCP/IP Configuration for Windows 95/98 Install TCP/IP Protocol into Your PCSet TCP/IP Protocol for Working with NAT Router MSI RG60G MSI RG60G Configure IP manually MSI RG60G PC1 Authentication ServerEquipment Details PC2Setup Windows 2000 Radius Server DUT and Windows 2000 Radius Server SetupConfiguration Setup DUTSetup Network adapter on PC Enable Ieee 802.1X access controlWindows 2000 Radius server Authentication testing Smart card or other Certificate PropertiesCertificate information on PC1 DUT authenticate PC2 using PEAP-TLS Appendix C WPA-PSK and WPA WPA-PSK Method1MSI RG60G Back to Connection Method2MSI RG60G WPA MethodMSI RG60G Then Choose certificate like above MSI RG60G Result Choose View available Wireless Networks like below MSI RG60G Appendix D FAQ Troubleshooting Reset to factory DefaultHardware and Port Characteristic Operational & Functional CharacteristicWireless Support Environment, Certification and Reliability