MSI manual MSI RG60G

Page 23

MSI RG60G

4.Connection ID: optional. Input the connection ID if your ISP requires it.

5.Maximum Idle Time: the time of no activity to disconnect your PPTP session. Set it to zero or enable Auto-reconnect to disable this feature. If Auto-reconnect is enabled, this product will connect to ISP automatically, after system is restarted or connection is dropped.

6.Connection Control: There are 3 modes to select:

Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.

Auto-Reconnect(Always-on): The device will link with ISP until the connection is established.

Manually: The device will not make the link until someone clicks the connect-button in the staus-page.

Turbo 802.11b/g 4 Port Wireless Broadband Router	17

Image 23

Contents MSI RG60G Luxembourg Ieee 802.11b/g and Bluetooth 2.4 GHz operationIeee 802.11b/g und Bluetooth 2.4 GHz Betrieb ItalyMSI Technology GmbH Operating rangeHinweise zur Reichweite Revision History Date First Release July Important Safety Precautions Table of Content Functions and Features Ieee 802.11b compatible 11M High speed for wireless LAN connectionStatistics of WAN Supported RoamingSystem time Supported SPI Mode SupportedSupport WPA-PSK and WPA DoS Attack Detection SupportedPacking List Panel Layout Hardware InstallationRear Panel Antenna LAN Ports 1~4 Power WAN PortSetup WAN connection Procedure for Hardware InstallationDecide where to place your Wireless Broadband Router Setup LAN connectionPing Make Correct Network Settings of Your ComputerMSI RG60G Configuring Wireless Broadband Router Wizard Start-up and LogSetup Press Change IP Setting WAN Type, IP ModeDynamic IP Address Static IP AddressPptp PPP over Ethernet1.6 L2TP MSI RG60G Wireless Setting and 802.1X setting ＊ Wireless settings Radius Shared Key ＊ 802.1X SettingWPA-PSK WPA2-PSK AES WPA2 AES WPA1/WPA2 3 WDS Dynamic DNS Dhcp Server Click More Advanced DoS Attack Detection Basic Setting Discard Ping from WAN sideSPI Mode MAC Address Control IP Address Packet Filtering Example ＊ Inbound FilterField MSI RG60G ＊ Privilege IP Addresses Range ＊ Domain Filter EnableDomain Filtering ＊ Domain Filter ＊ Log DNS Query＊ Enable URL Filtering ＊ URL Blocking EnableMSI RG60G Routing Table Destination Subnet Mask Gateway Hop Enabled Click Add New Rule Schedule RuleDelete After configure Rule 1à Schedule EnableEdit MSI RG60G Virtual Server ＊ Non-standard FTP port 9 DMZ ＊ IP Address of DMZ HostSpecial AP Recommended AdministrationChange Password Backup Setting Firmware UpgradeSystem Time Reset to factory defaultReboot ＊ Time Zone Remote Access ＊ Remote Administrator Host/Port＊ Get Date and Time by NTP Protocol ＊ Time ServerNetwork wake-up ＊ MAC Address for Wake-on-LAN ＊ Administrator Time-outStatus DiagnosticSystem Log System Status＊ Smtp Server IP and Port ＊ E-mail Alert EnableLog Notification ＊ IP Address for Syslog＊ Set Community Snmp Setting＊ Enable Snmp ＊ Get CommunityConfiguring Turbo Mode With Client Select Optimize for performance mode Configuration Confirmation Install TCP/IP Protocol into Your PC Appendix a TCP/IP Configuration for Windows 95/98Set TCP/IP Protocol for Working with NAT Router MSI RG60G MSI RG60G Configure IP manually MSI RG60G PC2 Authentication ServerEquipment Details PC1Setup DUT DUT and Windows 2000 Radius Server SetupConfiguration Setup Windows 2000 Radius ServerEnable Ieee 802.1X access control Setup Network adapter on PCSmart card or other Certificate Properties Windows 2000 Radius server Authentication testingCertificate information on PC1 DUT authenticate PC2 using PEAP-TLS Appendix C WPA-PSK and WPA Method1 WPA-PSKMSI RG60G Method2 Back to ConnectionMSI RG60G Method WPAMSI RG60G Then Choose certificate like above MSI RG60G Result Choose View available Wireless Networks like below MSI RG60G Reset to factory Default Appendix D FAQ TroubleshootingOperational & Functional Characteristic Hardware and Port CharacteristicEnvironment, Certification and Reliability Wireless Support