MSI RG60G manual Appendix D FAQ Troubleshooting, Reset to factory Default

Page 90

MSI RG60G

Appendix D FAQ and

Troubleshooting

Reset to factory Default

There are 2 methods to reset to default.

＊Restore with RESET button

First, turn off the router and press the RESET button in. And then, power on the router and push the RESET button down until the M1 and or M2 LED (or Status LED) start flashing, then remove the finger. If LED flashes about 8 times, the RESTORE process is completed. However, if LED flashes 2 times, repeat.

＊2. Restore directly when the router power on

First, push the RESET button about 5 seconds (M1 will start flashing about 5 times), remove the finger

. The RESTORE process is completed.

84Turbo 802.11b/g 4 Port Wireless Broadband Router

Image 90

Contents MSI RG60G Italy Ieee 802.11b/g and Bluetooth 2.4 GHz operationIeee 802.11b/g und Bluetooth 2.4 GHz Betrieb LuxembourgOperating range Hinweise zur ReichweiteMSI Technology GmbH Revision History Date First Release July Important Safety Precautions Table of Content Functions and Features Roaming High speed for wireless LAN connectionStatistics of WAN Supported Ieee 802.11b compatible 11MDoS Attack Detection Supported SPI Mode SupportedSupport WPA-PSK and WPA System time SupportedPacking List Hardware Installation Panel LayoutAntenna LAN Ports 1~4 Power WAN Port Rear PanelSetup LAN connection Procedure for Hardware InstallationDecide where to place your Wireless Broadband Router Setup WAN connectionMake Correct Network Settings of Your Computer PingMSI RG60G Configuring Wireless Broadband Router Start-up and Log WizardSetup IP Setting WAN Type, IP Mode Press ChangeStatic IP Address Dynamic IP AddressPPP over Ethernet Pptp1.6 L2TP MSI RG60G Wireless Setting and 802.1X setting ＊ Wireless settings ＊ 802.1X Setting Radius Shared KeyWPA-PSK WPA2-PSK AES WPA2 AES WPA1/WPA2 3 WDS Dynamic DNS Dhcp Server Click More Advanced Basic Setting Discard Ping from WAN side SPI ModeDoS Attack Detection MAC Address Control IP Address Packet Filtering ＊ Inbound Filter ExampleField MSI RG60G ＊ Log DNS Query ＊ Domain Filter EnableDomain Filtering ＊ Domain Filter ＊ Privilege IP Addresses Range＊ Enable ＊ URL Blocking Enable URL FilteringMSI RG60G Routing Table Destination Subnet Mask Gateway Hop Enabled Schedule Rule Click Add New RuleAfter configure Rule 1à Schedule Enable EditDelete MSI RG60G Virtual Server 9 DMZ ＊ IP Address of DMZ Host ＊ Non-standard FTP portSpecial AP Administration Change PasswordRecommended Firmware Upgrade Backup SettingReset to factory default RebootSystem Time ＊ Time Server Remote Access ＊ Remote Administrator Host/Port＊ Get Date and Time by NTP Protocol ＊ Time Zone＊ Administrator Time-out Network wake-up ＊ MAC Address for Wake-on-LANDiagnostic StatusSystem Status System Log＊ IP Address for Syslog ＊ E-mail Alert EnableLog Notification ＊ Smtp Server IP and Port＊ Get Community Snmp Setting＊ Enable Snmp ＊ Set CommunityConfiguring Turbo Mode With Client Select Optimize for performance mode Configuration Confirmation Appendix a TCP/IP Configuration for Windows 95/98 Install TCP/IP Protocol into Your PCSet TCP/IP Protocol for Working with NAT Router MSI RG60G MSI RG60G Configure IP manually MSI RG60G PC1 Authentication ServerEquipment Details PC2Setup Windows 2000 Radius Server DUT and Windows 2000 Radius Server SetupConfiguration Setup DUTSetup Network adapter on PC Enable Ieee 802.1X access controlWindows 2000 Radius server Authentication testing Smart card or other Certificate PropertiesCertificate information on PC1 DUT authenticate PC2 using PEAP-TLS Appendix C WPA-PSK and WPA WPA-PSK Method1MSI RG60G Back to Connection Method2MSI RG60G WPA MethodMSI RG60G Then Choose certificate like above MSI RG60G Result Choose View available Wireless Networks like below MSI RG60G Appendix D FAQ Troubleshooting Reset to factory DefaultHardware and Port Characteristic Operational & Functional CharacteristicWireless Support Environment, Certification and Reliability