MSI 3200 Network manual Installing Memory Modules, DDR2

Page 23

Hardware Setup

Memory

These DIMM slots are intended for system memory modules.

DDR2

240-pin, 1.8V

64x2=128 pin

56x2=112 pin

Installing Memory Modules

1.Locate the DIMM slots on the mainboard. Flip open the retaining clip at each side of the DIMM slot.

2.Align the notch on the DIMM with the key on the slot. Insert the DIMM vertically into the DIMM slot. Then push it in until the golden finger on the DIMM is deeply inserted in the DIMM slot. The retaining clip at each side of the DIMM slot will automatically close if the DIMM is properly seated.

Important

You can barely see the golden finger if the DIMM is properly inserted in the DIMM slot.

3.Manually check if the DIMM has been locked in place by the retaining clips at the sides.

Volt Notch

2-7

Image 23
Contents MS-91A2 V1.X Server Board NetworkTechnical Support Copyright NoticeTrademarks Revision HistorySafety Instructions FCC-B Radio Frequency Interference Statement Micro-Star International MS-91A2Weee Waste Electrical and Electronic Equipment Statement Page Vii Contents Getting Started IDE Mainboard SpecificationsFSB LANSlot/Golden Finger DimensionGetting Started Graphics Onboard I/ONetwork MS-91A2 V1.X Server Board Mainboard LayoutGetting Started Watch Dog Timer SettingSetup procedures MS-91A2 Server Board Getting Started Page Hardware Setup JCMOS1, p.2-21 JPWR1, p.2-8 Quick Components GuideIntroduction to LGA 775 CPU Hardware SetupCPU Central Processing Unit CPU & Cooler Installation Lift the load lever up and open the load plate Locking switch DDR2 Installing Memory ModulesMemory JPWR1 Power SupplyPin System Power Connector JPWR1 Pin CPU Power Connector JPWR2GbE LAN Ports Front Panel I/OUSB Port LAN1 ~ LAN5 GbE RJ-45 LAN port LAN Bypass Definition Bypass setting in BiosBit Definition Pwron Signal ActionPwroff Signal Action Set Bit 2 and 3 to Low Set Bit 0 and 1 to HighSet Bit 0 and 1 to Low Set Bit 2 and 3 to HighIDE1 ConnectorIDE Connector IDE1 SATA1 SATA2 SATA3 SATA4 SPI Flash ROM Connector JSPI1Serial ATA Connector SATA1 ~ SATA4 JSPI1CPUFAN1 SYSFAN1/2, FRONTFAN1 Serial Port Connector COM2Fan Power Connector CPUFAN1, SYSFAN1/2, FRONTFAN1 COMUSB 2.0 Bracket VGA Connector VGA1Front USB Connector JUSB1 JUSB1Front Panel Connector JFP1 LCD Module Connector JLCD1Power Button JPBTN1 JP1 Keyboard/Mouse Connector J3Cpld Data Reflash PinheaderJP1 JLED1 LAN LED Connector JLED1Clear Cmos Jumper JCMOS1 Bios Recovery Jumper JBOOT1JBOOT1 JumperPCI Express Slot / Golden FingerGolden Finger Mini PCI SlotCF Voltage Selecting Jumper JCFVSEL1 CF Mode Selecting Jumper JCFSEL1CompactFlash Card Slot CF1 Optional Page Bios Setup Press Del to enter Setup Entering SetupGeneral Help F1 Control KeysGetting Help Menu Bar System Date AMI BIOS, Processor, System MemoryMain System TimeAdvanced CPU ConfigurationPrimary/Secondary/Third/Fourth/Fifth IDE Master/Slave Bios Setup IntelR SpeedSteptm TechIDE Configuration Sata Configuration JMicron 36x ATA Controller Super IO ConfigurationCpufan / SYSFAN1 / SYSFAN2 Smart Fan Bios Setup Serial Port 1 Address, Serial Port 2 AddressHardware Health Configuration WDT FunctionResume On PME# Resume On RTC AlarmClear Event Log Bios Setup Event Log Configuration View Event LogMark All Events as Read VT-UTF8 Combo Key Support MS-91A2 Server Board Console Redirection Remote AccessRedirection After Bios Post Terminal TypeUSB Mass Storage Device Configuration Bios Setup Sredir Memory Display DelayUSB Configuration Legacy USB Support Emulation Type MS-91A2 Server Board USB Mass Storage Reset DelayBoot Settings Configuration BootWait For ‘F1’ If Error MS-91A2 Server Board Quick BootQuiet Boot Bootup Num-LockRemovable Drives 1st Drive, 2nd Drive Bios Setup Boot Device Priority 1st Boot DeviceSecurity Supervisor Password / Change Supervisor PasswordUser Password / Change User Password Chipset Exit