MSI 3200 Network manual Bios Setup Boot Device Priority 1st Boot Device

Page 57

BIOS Setup

Boot Device Priority

1st Boot Device

The items allow you to set the sequence of boot devices where BIOS attempts to load the disk operating system. First press <Enter> to enter the sub-menu. Then you may use the arrow keys ( −↓ ) to select the desired device, then press <+>, <-> or <PageUp>, <PageDown> key to move it up/down in the priority list.

Removable Drives

1st Drive, 2nd Drive

This setting allows users to set the priority of the removable devices. First press <Enter> to enter the sub-menu. Then you may use the arrow keys ( −↓ ) to select the desired device, then press <+>, <-> or <PageUp>, <PageDown> key to move it up/down in the priority list.

3-17

Image 57
Contents MS-91A2 V1.X Server Board NetworkTrademarks Copyright NoticeRevision History Technical SupportSafety Instructions FCC-B Radio Frequency Interference Statement Micro-Star International MS-91A2Weee Waste Electrical and Electronic Equipment Statement Page Vii Contents Getting Started FSB Mainboard SpecificationsLAN IDEGetting Started Graphics DimensionOnboard I/O Slot/Golden FingerNetwork MS-91A2 V1.X Server Board Mainboard LayoutWatch Dog Timer Setting Setup proceduresGetting Started MS-91A2 Server Board Getting Started Page Hardware Setup JCMOS1, p.2-21 JPWR1, p.2-8 Quick Components GuideHardware Setup CPU Central Processing UnitIntroduction to LGA 775 CPU CPU & Cooler Installation Lift the load lever up and open the load plate Locking switch Installing Memory Modules MemoryDDR2 Pin System Power Connector JPWR1 Power SupplyPin CPU Power Connector JPWR2 JPWR1Front Panel I/O USB PortGbE LAN Ports LAN1 ~ LAN5 GbE RJ-45 LAN port LAN Bypass Definition Bypass setting in BiosPwron Signal Action Pwroff Signal ActionBit Definition Set Bit 0 and 1 to Low Set Bit 0 and 1 to HighSet Bit 2 and 3 to High Set Bit 2 and 3 to LowConnector IDE Connector IDE1IDE1 Serial ATA Connector SATA1 ~ SATA4 SPI Flash ROM Connector JSPI1JSPI1 SATA1 SATA2 SATA3 SATA4Fan Power Connector CPUFAN1, SYSFAN1/2, FRONTFAN1 Serial Port Connector COM2COM CPUFAN1 SYSFAN1/2, FRONTFAN1Front USB Connector JUSB1 VGA Connector VGA1JUSB1 USB 2.0 BracketLCD Module Connector JLCD1 Power Button JPBTN1Front Panel Connector JFP1 Keyboard/Mouse Connector J3 Cpld Data Reflash PinheaderJP1JP1 JLED1 LAN LED Connector JLED1JBOOT1 Bios Recovery Jumper JBOOT1Jumper Clear Cmos Jumper JCMOS1Golden Finger Slot / Golden FingerMini PCI Slot PCI ExpressCF Mode Selecting Jumper JCFSEL1 CompactFlash Card Slot CF1 OptionalCF Voltage Selecting Jumper JCFVSEL1 Page Bios Setup Press Del to enter Setup Entering SetupControl Keys Getting HelpGeneral Help F1 Menu Bar Main AMI BIOS, Processor, System MemorySystem Time System DateAdvanced CPU ConfigurationBios Setup IntelR SpeedSteptm Tech IDE Configuration Sata ConfigurationPrimary/Secondary/Third/Fourth/Fifth IDE Master/Slave JMicron 36x ATA Controller Super IO ConfigurationHardware Health Configuration Bios Setup Serial Port 1 Address, Serial Port 2 AddressWDT Function Cpufan / SYSFAN1 / SYSFAN2 Smart FanResume On PME# Resume On RTC AlarmBios Setup Event Log Configuration View Event Log Mark All Events as ReadClear Event Log Redirection After Bios Post MS-91A2 Server Board Console Redirection Remote AccessTerminal Type VT-UTF8 Combo Key SupportBios Setup Sredir Memory Display Delay USB Configuration Legacy USB SupportUSB Mass Storage Device Configuration Emulation Type MS-91A2 Server Board USB Mass Storage Reset DelayBoot Settings Configuration BootQuiet Boot MS-91A2 Server Board Quick BootBootup Num-Lock Wait For ‘F1’ If ErrorRemovable Drives 1st Drive, 2nd Drive Bios Setup Boot Device Priority 1st Boot DeviceSupervisor Password / Change Supervisor Password User Password / Change User PasswordSecurity Chipset Exit