MSI 3200 Network manual MS-91A2 Server Board Console Redirection Remote Access, Terminal Type

Page 52

MS-91A2 Server Board

Console Redirection

Remote Access

The setting enables/disables the remote access function. When set to [Enabled], users may configure the following settings for remote access type and parameters.

Serial Port Number, Base Address, IRQ, Serial Port Mode Use these settings to configure ports for remote access.

Flow Control

Flow control is the process of managing the rate of data transmission between two nodes. It’s the process of adjusting the flow of data from one device to another to ensure that the receiving device can handle all of the incoming data. This is particularly important where the sending device is capable of sending data much faster than the receiving device can receive it.

Redirection After BIOS POST

This setting determines whether or not to keep terminals’ console redirection running after the BIOS POST has booted.

Terminal Type

To operate the system’s console redirection, you need a terminal supporting ANSI terminal protocol and a RS-232 null modem cable connected between the host system and terminal(s). This setting specifies the type of terminal device for console redirection.

VT-UTF8 Combo Key Support

This setting enables/disables the VT-UTF8 combination key support for ANSI/ VT100 terminals.

3-12

Image 52
Contents Network MS-91A2 V1.X Server BoardCopyright Notice TrademarksRevision History Technical SupportSafety Instructions Micro-Star International MS-91A2 FCC-B Radio Frequency Interference StatementWeee Waste Electrical and Electronic Equipment Statement Page Vii Contents Getting Started Mainboard Specifications FSBLAN IDEDimension Getting Started GraphicsOnboard I/O Slot/Golden FingerMainboard Layout Network MS-91A2 V1.X Server BoardSetup procedures Watch Dog Timer SettingGetting Started MS-91A2 Server Board Getting Started Page Hardware Setup Quick Components Guide JCMOS1, p.2-21 JPWR1, p.2-8CPU Central Processing Unit Hardware SetupIntroduction to LGA 775 CPU CPU & Cooler Installation Lift the load lever up and open the load plate Locking switch Memory Installing Memory ModulesDDR2 Power Supply Pin System Power Connector JPWR1Pin CPU Power Connector JPWR2 JPWR1USB Port Front Panel I/OGbE LAN Ports LAN1 ~ LAN5 GbE RJ-45 LAN port Bypass setting in Bios LAN Bypass DefinitionPwroff Signal Action Pwron Signal ActionBit Definition Set Bit 0 and 1 to High Set Bit 0 and 1 to LowSet Bit 2 and 3 to High Set Bit 2 and 3 to LowIDE Connector IDE1 ConnectorIDE1 SPI Flash ROM Connector JSPI1 Serial ATA Connector SATA1 ~ SATA4JSPI1 SATA1 SATA2 SATA3 SATA4Serial Port Connector COM2 Fan Power Connector CPUFAN1, SYSFAN1/2, FRONTFAN1COM CPUFAN1 SYSFAN1/2, FRONTFAN1VGA Connector VGA1 Front USB Connector JUSB1JUSB1 USB 2.0 BracketPower Button JPBTN1 LCD Module Connector JLCD1Front Panel Connector JFP1 Cpld Data Reflash PinheaderJP1 Keyboard/Mouse Connector J3JP1 LAN LED Connector JLED1 JLED1Bios Recovery Jumper JBOOT1 JBOOT1Jumper Clear Cmos Jumper JCMOS1Slot / Golden Finger Golden FingerMini PCI Slot PCI ExpressCompactFlash Card Slot CF1 Optional CF Mode Selecting Jumper JCFSEL1CF Voltage Selecting Jumper JCFVSEL1 Page Bios Setup Entering Setup Press Del to enter SetupGetting Help Control KeysGeneral Help F1 Menu Bar AMI BIOS, Processor, System Memory MainSystem Time System DateCPU Configuration AdvancedIDE Configuration Sata Configuration Bios Setup IntelR SpeedSteptm TechPrimary/Secondary/Third/Fourth/Fifth IDE Master/Slave Super IO Configuration JMicron 36x ATA ControllerBios Setup Serial Port 1 Address, Serial Port 2 Address Hardware Health ConfigurationWDT Function Cpufan / SYSFAN1 / SYSFAN2 Smart FanResume On RTC Alarm Resume On PME#Mark All Events as Read Bios Setup Event Log Configuration View Event LogClear Event Log MS-91A2 Server Board Console Redirection Remote Access Redirection After Bios PostTerminal Type VT-UTF8 Combo Key SupportUSB Configuration Legacy USB Support Bios Setup Sredir Memory Display DelayUSB Mass Storage Device Configuration MS-91A2 Server Board USB Mass Storage Reset Delay Emulation TypeBoot Boot Settings ConfigurationMS-91A2 Server Board Quick Boot Quiet BootBootup Num-Lock Wait For ‘F1’ If ErrorBios Setup Boot Device Priority 1st Boot Device Removable Drives 1st Drive, 2nd DriveUser Password / Change User Password Supervisor Password / Change Supervisor PasswordSecurity Chipset Exit