MSI 3200 Network manual Front Panel I/O, USB Port, GbE LAN Ports

Page 25

Hardware Setup

Front Panel I/O

 

USB Ports

 

 

 

 

 

 

 

LED1

LED2

 

 

 

 

 

COM1 Serial

LAN7 GbE

LAN6 GbE

LAN4

LAN5

LAN2

LAN3

LAN1 GbE

GbE RJ-45 LAN

GbE RJ-45 LAN

Console Port

Fiber SFP

Fiber SFP

RJ-45 LAN

(Bypass Pair 2)

(Bypass Pair 1)

 

LAN

LAN

 

 

 

 

 

 

 

LAN

WAN

LAN

WAN

LAN

WAN

LAN

WAN

LAN Bypass Disable

LAN Bypass Enable

NOTE: LAN bypass function only works in the event of AC power down.

USB Port

The USB (Universal Serial Bus) port is for attaching USB devices such as keyboard, mouse, or other USB-compatible devices.

GbE LAN Ports

LAN6 ~ LAN7: GbE SFP LAN port

Insert your fiber SFP (Small Form-Factor Pluggable) transceiver module into the Mini GBIC SFP port and connect the optical fiber network cable to the SFP module.

2-9

Image 25
Contents MS-91A2 V1.X Server Board NetworkTrademarks Copyright NoticeRevision History Technical SupportSafety Instructions FCC-B Radio Frequency Interference Statement Micro-Star International MS-91A2Weee Waste Electrical and Electronic Equipment Statement Page Vii Contents Getting Started FSB Mainboard SpecificationsLAN IDEGetting Started Graphics DimensionOnboard I/O Slot/Golden FingerNetwork MS-91A2 V1.X Server Board Mainboard LayoutSetup procedures Watch Dog Timer SettingGetting Started MS-91A2 Server Board Getting Started Page Hardware Setup JCMOS1, p.2-21 JPWR1, p.2-8 Quick Components GuideCPU Central Processing Unit Hardware SetupIntroduction to LGA 775 CPU CPU & Cooler Installation Lift the load lever up and open the load plate Locking switch Memory Installing Memory ModulesDDR2 Pin System Power Connector JPWR1 Power SupplyPin CPU Power Connector JPWR2 JPWR1USB Port Front Panel I/OGbE LAN Ports LAN1 ~ LAN5 GbE RJ-45 LAN port LAN Bypass Definition Bypass setting in BiosPwroff Signal Action Pwron Signal ActionBit Definition Set Bit 0 and 1 to Low Set Bit 0 and 1 to HighSet Bit 2 and 3 to High Set Bit 2 and 3 to LowIDE Connector IDE1 ConnectorIDE1 Serial ATA Connector SATA1 ~ SATA4 SPI Flash ROM Connector JSPI1JSPI1 SATA1 SATA2 SATA3 SATA4Fan Power Connector CPUFAN1, SYSFAN1/2, FRONTFAN1 Serial Port Connector COM2COM CPUFAN1 SYSFAN1/2, FRONTFAN1Front USB Connector JUSB1 VGA Connector VGA1JUSB1 USB 2.0 BracketPower Button JPBTN1 LCD Module Connector JLCD1Front Panel Connector JFP1 Cpld Data Reflash PinheaderJP1 Keyboard/Mouse Connector J3JP1 JLED1 LAN LED Connector JLED1JBOOT1 Bios Recovery Jumper JBOOT1Jumper Clear Cmos Jumper JCMOS1Golden Finger Slot / Golden FingerMini PCI Slot PCI ExpressCompactFlash Card Slot CF1 Optional CF Mode Selecting Jumper JCFSEL1CF Voltage Selecting Jumper JCFVSEL1 Page Bios Setup Press Del to enter Setup Entering SetupGetting Help Control KeysGeneral Help F1 Menu Bar Main AMI BIOS, Processor, System MemorySystem Time System DateAdvanced CPU ConfigurationIDE Configuration Sata Configuration Bios Setup IntelR SpeedSteptm TechPrimary/Secondary/Third/Fourth/Fifth IDE Master/Slave JMicron 36x ATA Controller Super IO ConfigurationHardware Health Configuration Bios Setup Serial Port 1 Address, Serial Port 2 AddressWDT Function Cpufan / SYSFAN1 / SYSFAN2 Smart FanResume On PME# Resume On RTC AlarmMark All Events as Read Bios Setup Event Log Configuration View Event LogClear Event Log Redirection After Bios Post MS-91A2 Server Board Console Redirection Remote AccessTerminal Type VT-UTF8 Combo Key SupportUSB Configuration Legacy USB Support Bios Setup Sredir Memory Display DelayUSB Mass Storage Device Configuration Emulation Type MS-91A2 Server Board USB Mass Storage Reset DelayBoot Settings Configuration BootQuiet Boot MS-91A2 Server Board Quick BootBootup Num-Lock Wait For ‘F1’ If ErrorRemovable Drives 1st Drive, 2nd Drive Bios Setup Boot Device Priority 1st Boot DeviceUser Password / Change User Password Supervisor Password / Change Supervisor PasswordSecurity Chipset Exit