Lennox International Inc LENNOX Elite Series XP13 Units HEAT PUMPS, 06/11 50672801 Off

Page 29

Compressor Delay (P5)

The defrost control has a field−selectable function to reduce occasional sounds that may occur while the unit is cycling in and out of the defrost mode.

SUnits with defrost control 100269−02: The compressor will be cycled off for 30 seconds going in and out of the defrost mode when the compressor delay jumper is removed.

SUnits with defrost control 100269−04: The compressor will be cycled off for 30 seconds going in and out of the defrost mode when the compressor delay jumper is installed.

NOTE

when jumpering the TEST pins. Time Delay

The timed-off delay is five minutes long. The delay helps to protect the compressor from short-cycling in case the power to the unit is interrupted or a pressure switch opens. The delay is bypassed by placing the timer select jumper across the TEST pins for 0.5 seconds.

Test Mode (P1)

A TEST option is provided for troubleshooting. The TEST mode may be started any time the unit is in the heating mode and the defrost thermostat is closed or jumpered. If the jumper is in the TEST position at

power-up, the defrost control will ignore the test pins. When the jumper is placed across the TEST pins for two seconds, the defrost control will enter the defrost mode. If the jumper is removed before an additional 5−second period has elapsed (7 seconds total), the unit will remain in defrost mode until the defrost thermostat opens or 14 minutes have passed. If the jumper is not removed until after the additional 5−second period has elapsed, the defrost will terminate and the test option will not function again until the jumper is removed and re−applied.

Defrost Control Diagnostic LEDs

The defrost board uses two LEDs for diagnostics. The LEDs flash a specific sequence according to the condition.

Table 6. Defrost Control (CMC1) Diagnostic LEDs

Mode

Green LED (DS2)

Red LED (DS1)

 

 

 

No power to con-

OFF

OFF

trol

 

 

 

 

 

Normal operation /

Simultaneous Slow FLASH

power to control

 

 

 

 

 

Anti-short cycle

Alternating Slow FLASH

lockout

 

 

 

 

 

High pressure

Slow FLASH

OFF

switch fault

 

 

 

 

 

High pressure

ON

OFF

switch lockout

 

 

 

 

 

Page 29

XP13 SERIES

Page 28 Page 30
Image 29
Page 28 Page 30
Contents General Table of ContentsShipping and Packing List Model Number Identification 13 −036 − 230 −08 Unit Dimensions − Inches mmSide View TOP ViewControl Panel PLUMBING, Switches Sensor ComponentsTypical Unit Parts Arrangement Operating Service Valves Operating Gauge Set and Service ValvesUsing Manifold Gauge SET Caps and Fasteners Torque RequirementsReinstall Stem Cap Operating Angle−Type Service ValveOperating Ball−Type Service Valve 1DISCONNECT Power Recovering Refrigerant from Existing System3RECOVERING Refrigerant Method Method 2 LimitationsNew Outdoor Unit Placement Placement, Slab Mounting and Stabilizing Unit Detail a Outside Unit PlacementLouvered Panel Removal Removing and Installing PanelsLouvered Panel Installation Using Existing Line SET NEW or Replacement Line SET InstallationLine Set Requirements Adding Polyol Ester OIL RequirementsRefrigerant Line SET Alling Horizontal Runs Refrigerant Line SET From Vertical to HorizontalBrazing Connections 2CAP and Core Removal 1CUT and DeburFlow Nitrogen Wrap Service Valves6BRAZE Line SET Preparation for Next Step3FLUSHING Line SET 2CONNECT Gauges and Equipment for Flushing ProcedureIndoor Expansion Valve Installation Installing New Indoor Metering DeviceSensing Bulb Installation Equalizer Line InstallationTest for Leaks Leak Test Line Set and Indoor CoilConnect Gauge SET 2EVACUATE the System Evacuating Line Set and Indoor Coil2INSTALL Thermostat Size Circuit and Install DisconnectElectrical 24VAC TransformerTypical Unit Wiring Diagram Unit START−UP Unit Start−UpConnections for Optimizing System Charge Leak CHECK, Repair and EvacuateConnect Manifold Gauge SET and WEIGH−IN Charge Calculating System Charge for Outdoor Unit Void of Charge Using HFC−410A Weigh In MethodAdjusting Indoor Airflow Optimizing ProcedureOptimizing System Refrigerant Charge CFM =SCº SATº LIQºIf subcooling value is RefrigerantNormal Operating Pressures − Liquid +10 and Vapor +5 Psig HFC−410A Temperature F − Pressure Psig Defrost Control CMC1 System OperationDefrost System OFF Dealer MaintenanceIndoor Unit Indoor CoilXP13 Series Installer City Start−Up and Performance ChecklistJob Name Job no Date Job Location City Sequence of Operation Thermostat

LENNOX Elite Series XP13 Units HEAT PUMPS, 06/11 50672801 specifications

Lennox International Inc., a leading name in the HVAC (heating, ventilation, and air conditioning) industry, has a reputation for delivering high-quality and energy-efficient systems. One of the standout products in their lineup is the Lennox Elite Series XP13 heat pump, model number 50672801. This heat pump is designed to provide exceptional comfort throughout the year while offering efficiency and reliability that homeowners can depend on.

The Lennox Elite Series XP13 heat pump features a compact design that makes it suitable for various outdoor spaces. One of its main characteristics is its efficiency, boasting a SEER (Seasonal Energy Efficiency Ratio) rating of up to 16 and an HSPF (Heating Seasonal Performance Factor) of up to 9. This means that the XP13 can help reduce energy bills, making it an eco-friendly choice for homeowners looking to minimize their carbon footprint.

This heat pump utilizes advanced technology to ensure optimal performance. The XP13 is equipped with a scroll compressor, which operates quietly and efficiently compared to traditional compressors. This feature ensures a more reliable and consistent temperature control, which translates to enhanced comfort levels in the home. Moreover, the XP13 is designed with a sound-dampening system that reduces operational noise, making it one of the quieter options in the market.

Another key aspect of the XP13 heat pump is its innovative use of advanced coil technology. The unit's coils are made from high-grade aluminum, which promotes superior heat exchange and improves overall efficiency. In addition, the XP13 is designed with a built-in filter drier that helps remove moisture and contaminants from the refrigerant, protecting the system from potential damage and enhancing its lifespan.

The XP13 model is compatible with the iComfort S30 smart thermostat, allowing users to control their home’s temperature remotely. This smart technology provides energy-saving options and real-time updates, ensuring that homeowners can optimize their HVAC systems for both comfort and efficiency.

Overall, the Lennox Elite Series XP13 heat pump, model 50672801, exemplifies a commitment to delivering high-performance heating and cooling solutions. With its energy-efficient design, advanced technologies, and features aimed at enhancing user comfort and convenience, the XP13 remains a top choice among homeowners looking for a reliable and effective heat pump system.
Top Page Image Contents