Makita 4013D, 4033D English, Additional Safety Rules, Operating Instructions, Specifications

ENGLISH

Explanation of general view

1	Battery cartridge	5	Switch lever	9	Corner nozzle
2	Push button	6	Hook	10	Nozzle
3	Screw	7	Front lip	11	Extension wand (Straight pipe)
4	Set plate	8	Cleaner body

SPECIFICATIONS

Model	4013D	4033D
Capacities	0.5 L	0.5 L
Continuous use (with battery 1222/1422)	Approx. 14min.	Approx. 14 min.
Overall length	465 mm	473 mm
Net weight	0.89 kg	0.89 kg
Rated voltage	D.C. 12 V	D.C. 14.4 V

•Due to our continuing program of research and devel- opment, the specifications herein are subject to change without notice.

•Note: Specifications may differ from country to country.

Safety hints

For your own safety, please refer to the enclosed safety instructions.

ADDITIONAL SAFETY RULES

1.Read this instruction manual and the charger instruction manual carafully before use.

2.Do not pick up wet materials, lit cigarettes or the like.

3.Stop operation immediately if you notice any- thing abnormal.

4.If you drop or strike the cleaner, check it care- fully for cracks or damage before operation.

5.Do not bring close to stoves or other heat sources.

6.Do not block the intake hole or vent holes.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 1)

•Always switch off the cleaner before insertion or removal of the battery cartridge.

•To remove the battery cartridge, withdraw it from the cleaner while pressing the buttons on both sides of the cartridge.

•To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the cleaner, causing injury to you or someone around you.

•Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly.

Installing set plate (optional accessory) for 4013D only (Fig. 2)

Always install the set plate when using battery cartridges 1200, 1202 or 1202A. Install the set plate on the cleaner with the screw provided.

Charging

Charge the battery cartridge with your Makita charger properly before use.

Following batteries can be used for this cleaner;

Model	Battery type	Capacity	Number of
		(mAh)	cells
	1200, 1220	1300	10
4013D	1202, 1222, 1202A	2000	10
	1234	2600	10
	1235, 1235A	3000	10
	1420	1300	12
4033D	1422	2000	12
	1434	2600	12
	1435	3000	12

Switch action (Fig. 3)

CAUTION:

•Always be sure that the dust bag or paper filter is installed properly in the cleaner before use. Improper installation may allow dust to enter the motor, resulting in malfunction of the cleaner.

•Always switch off the cleaner after each use to prevent damage to the cleaner and to lengthen the service life of the batteries.

To start the cleaner, slide the switch lever forward to the “ I ” position.

To stop the cleaner, slide the switch lever back to the “ O ” position.

Dust disposal

CAUTION:

Empty the cleaner before it becomes too full, or the suc- tion force weakens.

Depress the buttons and open the front cover. (Fig. 4) Take the dust bag out of the cleaner carefully so that the contents will not spill out. Empty the contents out of the dust bag. (Fig. 5)

Also empty out the dust inside the cleaner itself. Failure to do so may cause the sponge filter to be clogged or the motor to be damaged. (Fig. 6)

4