Multiquip qp-402h manual QP-402H PRE-SETUP Pump

Page 17

Pre-Setup (Pump)

1.Read safety instructions at the beginning of manual.

2.Place pump as near to water as possible,onafirmflat,levelsurface.

3.Toprimepump,removefillcap(Figure2)andfillpumpcasing with water. If the pump casing is not filled with water before starting, it will not begin pumping.

CAUTION - Pump Casing

Pump casing must be filled with water before using pump. Otherwise pump will not be able to begin pumping.

WARNING - High Pressure

DO NOT open fill cap if pump is hot! Water inside may be under pressure. The possibility exists of scalding, resulting in severe bodily harm.

4.Checkforleaksbetweenpumpandengine.Ifwaterisleaking between the pump and engine housing, the seal inside the pumpmaybewornordamaged.Continued operationofthe pumpisnot recommended.Furtherusageofthe pumpunder theseconditionsmaycauseseverewaterdamagetoengine.

Hoses and Clamps

1.Check that all hoses are securely attached to the pump. Make certain suction hose (Figure 2) does not have any air leakage.Tighten hose clamps and couplings as required.

2.Itisrecommendedthat 2 clampsbeusedwhensecuringthe suction hose to the inlet side (suction) of the pump.

3.Remember suction hoses must be rigid enough not to collapse when the pump is in operation.

4.Check that the discharge hose (Figure 2) is not restricted. Place hose so that it lays as straight as it is possible on the ground. Remove any twists or sharp bends from hose which may block the flow of water.

QP-402HPRE-SETUP (PUMP)

Suction and discharge hoses are

NOTE available from Multiquip. Contact your nearest dealer for more information.

5.The discharge hose is usually a collapsible (thin-walled) hose, however if a thin-walled discharge hose is not avail- able, a rigid suction hose can be substituted in its place.

6.Make sure the suction strainer (Figure 2) is clean and securely attached to the water end of the suction hose. The strainer is designed to protect the pump by preventing large objects from being pulled into the pump.

CAUTION - Strainer

The strainer should be positioned so it will remain completely under water. Running the pump with the strainer above water for long periods can damage the pump.

CAUTION - Flammable Fluids-Chemicals

DO NOT pump flammable fluids, corrosive chemicals or fluids containing toxic substances. These fluids can create potentially dangerous health and environmental hazards. Contact local authorities for assistance.

CAUTION - Mechanical Seal

This pump uses a water-cooled mechanical seal to prevent water from seeping into the engine. The passage of water through the pump casing lubricates the seal and prevents it from overheating. NEVER! operate the pump without water in the casing as this will cause damage to the mechanical seal.

QP-402H CENTRIFUGAL PUMP — OPERATION AND PARTS MANUAL— REV. #1 (04/02/08) — PAGE 17

Image 17
Contents Model QP-402H Centrifugal Pump Proposition 65WARNING Page Table of Contents Ordering parts has never been easier Parts Ordering ProceduresFor Your Safety and the Safety of Others QP-402H Safety Message Alert SymbolsAlways wear approved eye and hearing protection QP-402H Safety Message Alert SymbolsQP-402H Rules for Safe Operation QP-402H Rules for Safe Operation Maintenance SafetyQP-402H SPECIFICATIONS/DIMENSIONS Pump Specifications PumpQP-402H SPECIFICATIONS/DIMENSIONS Engine Specifications EnginesApplication QP-402H General InformationQP-402H Pump Components Plastic TRUCK-BED Liner QP-402H RefuelingInitial Servicing QP-402H Basic EnginePre-Inspection Engine QP-402H PRE-INSPECTION EngineQP-402H PRE-SETUP Pump QP-402H Initial START-UP Engine Normal Shutdown QP-402H Initial START-UP EnginePump Vacuum Test QP-402H Maintenance PumpQP-402H Maintenance Pump Engine Maintenance Schedule QP-402H Maintenance EngineDaily QP-402H Maintenance EnginePump Storage QP-402H Preparation for Long -TERM StoragePage Engine Troubleshooting QP-402H Troubleshooting EngineEngine Troubleshooting QP-402H Troubleshooting ENGINE/PUMPQP-402H Explanation of Code in Remarks Column Sample Parts ListQP-402H Suggested Spare Parts Pump Assy QP-402H Pump AssySuction Cover CasingVolute Casing BaseAIR Cleaner Dual Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. AIR Cleaner Dual AssyCOLLAR, AIR Cleaner GROMMET, AIR CleanerCollar B, AIR Cleaner GASKET, ElbowCamshaft Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Camshaft AssyHonda GX240K1PMT2/GX240U1PMT2 ENG. Camshaft Assy Carburetor Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Carburetor AssyHonda GX240K1PMT2/GX240U1PMT2 ENG. Carburetor Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Carburetor Assy SPACER, Carburetor PLATE, Lever SettingGASKET, Carburetor GASKET, InsulatorControl Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Control AssyHonda GX240K1PMT2/GX240U1PMT2 ENG. Control Assy Crankcase Cover Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Crankcase CVR. AssyHOLDER, Governor Weight WEIGHT, GovernorPIN, Governor Weight GASKET, Case CoverCrankshaft Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Crankshaft Assy90741ZE2000 Honda GX240K1PMT2/GX240U1PMT2 ENG. Crankshaft AssyCylinder Barrel Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Cylinder Barrel AssyRING, 14MM NOK NUT, Flange 10MMPIN, Lock 10MM SHAFT, Governor ARMCylinder Head Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Cylinder Head AssyHonda GX240K1PMT2/GX240U1PMT2 ENG. Cylinder Head Assy FAN Cover Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. FAN Cover AssyHonda GX240K1PMT2/GX240U1PMT2 ENG. FAN Cover Assy Flywheel Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Flywheel AssyFLYWHEEL, Complete Honda GX240K1PMT2/GX240U1PMT2 ENG. Flywheel AssyFAN, Cooling NUT, Special 16MMFuel Tank Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Fueltank AssyHonda GX240K1PMT2/GX240U1PMT2 ENG. Fueltank Assy Ignition Coil Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Ignition Coil AssyHonda GX240K1PMT2/GX240U1PMT2 ENG. Ignition Coil Assy WIRE, Stop Switch 370 MMCoil ASSY., Ignition GROMMET, CordMuffler Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Muffler Assy Piston Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Piston AssyBOLT, Connecting ROD ROD ASSY., ConnectingRing SET, Piston STD Ring SET, PistonRecoil Starter Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Recoil Starter AssyHonda GX240K1PMT2/GX240U1PMT2 ENG. Recoil Starter Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Gasket KIT Assy 061A1ZE2040 Honda GX240K1PMT2/GX240U1PMT2 ENG. Gasket KIT AssyLabels Assy Honda GX240K1PMT2/GX240U1PMT2 ENG. Labels AssyMARK, Choke Orange MARK, Throttle IndicationMARK, Choke Gray LABEL, CautionFreight Policy Terms and Conditions of Sale PartsPage Heres HOW to GET Help

qp-402h specifications

The Multiquip QP-402H is a powerful, versatile piece of construction equipment designed for a range of applications, particularly in the construction and operational sectors. Known for its durability and efficiency, the QP-402H is a part of Multiquip’s extensive portfolio of equipment that adheres to the high standards of reliability and performance.

One of the standout features of the QP-402H is its robust Honda GX160 engine, which delivers superior power and performance. The engine is designed for optimal fuel efficiency, allowing operators to maximize their productivity while minimizing operational costs. This machine is engineered to handle a wide variety of tasks, from producing high-quality concrete to powering various construction tools, making it an invaluable asset on job sites.

In terms of design, the QP-402H features a heavy-duty construction, which ensures its longevity even under strenuous working conditions. The unit is equipped with an advanced compressor system that provides consistent air supply for up to four pneumatic tools simultaneously. This multi-tool capability significantly enhances productivity on the job site, allowing crews to work more efficiently without having to wait for equipment to become available.

The QP-402H incorporates sophisticated technologies to ensure user-friendly operation. Its intuitive controls are designed to be easily accessible, enabling operators to quickly adjust settings and manage functions with minimal effort. Additionally, the compact design of the unit allows for easy transportation and maneuverability, making it a suitable choice for both large scale and tight-space projects.

Another notable characteristic of the QP-402H is its low noise level, which is increasingly important in urban environments where noise regulations are strict. This quiet operation ensures that tasks can be completed with minimal disruption, promoting better relations with surrounding communities.

Safety is a primary consideration in the design of the Multiquip QP-402H. The machine is equipped with various safety features, including a protective cage for the engine and secure fastenings for operational stability. These features contribute to a safer working environment for operators and personnel on-site.

In conclusion, the Multiquip QP-402H stands out as a reliable, efficient, and versatile solution in the realm of construction equipment. Its powerful engine, user-friendly technologies, robust construction, and safety features make it an ideal choice for professionals who require high-performance equipment that can handle varied demands in challenging environments.