Samsung AWT18F1ME, AWT20F1MBA, AWT24F1ME Method of Installation, Checkpoints prior to installation

Page 12

Method of Installation

Before installation, be sure to check the installation area

for the air conditioner, and installation method of the drain hose.

Checkpoints prior to installation

1Check the cabinet and front grille of the unit for any harmful defects such as scratches.

2Be sure to check the power supply.

- Refer to the specifications on the label attached to the unit.

Installation Conditions

1As the unit is heavy, the wall or window of the installation area should have sufficient strength and durability for operation of the air conditioner, and for prevention of any vibration or noise.

If it is weak, reinforcement work should be performed separately.

2It is advisable to install the air conditioner in the north or west side to prevent the effect of direct sunlight.

When installing it in the south or east side due to unavoidable circumstances, it is advisable to install the sunshade to prevent the direct sunlight.

In this case, take care not to cause any hindrance to the flow of outside air.

3When installing the air conditioner, be sure to obtain sufficient space on the rear side of the unit for smooth flow of air.

When operating the air conditioner in closed areas such as inner building with cooling operation, and result in trouble with the unit.

See the illustration below.

 

 

Awning

 

 

75mm

 

 

 

min.

300mm

 

 

240mm

500mm

Fence, wall

500mm

500mm

 

or other

 

 

 

 

 

 

obstacle

 

 

Approx.3˚

 

750mm

 

150mm min.

 

Note If the wall is greater than 150mm thick, cut the wall back on a 45˚ angle if possible.

Outdoor side

45˚

 

 

 

45˚

Indoor side

100mm or more

E-12

Image 12
Contents OWNER’S Instructions Safety Precautions Contents Air Conditioning Unit Main Parts and Control Panel Getting Started Cooling Your Room To cool your roomWith a Selection dial to Switching the Air Conditioner Off Airing Your RoomAdjusting the Air Flow Direction Horizontally Adjusting the Air Flow Direction VerticallyAdjust the blades to face Temperature and Humidity Ranges Mode Outdoor Indoor Indoor Humidity TemperatureOperating Recommendation TopicRecommendationCleaning Your Air Conditioner Removal and Reassembly of the Front GrilleSolving Common Problems Technical SpecificationsMethod of Installation Checkpoints prior to installationInstallation Conditions Installation of the Drain Tube Installation of the Drain PanSafety clip Drain Pan Rear Rubber cap Memo This AIR Conditioner is Manufactured by

AWT24F1MEB/EC, AWT24F1MBA/BC, AWT24F1MB, AWT18F1MBB/BC, AWT24F1ME specifications

The Samsung AWT series presents a selection of advanced air conditioning units designed to provide optimal comfort and efficiency for varying space requirements. Models such as AWT18F1ME, AWT24F1MB, AWT20F1MB, and AWT24F1ME stand out in this lineup, each offering unique features and technologies tailored to meet diverse customer needs.

One of the key aspects of the AWT series is their energy efficiency. These models are equipped with inverter technology, enabling precise control over cooling and heating. Inverter systems adjust the compressor's speed based on the temperature set on the thermostat, resulting in significantly lower energy consumption compared to traditional systems. This not only helps reduce electricity bills but also minimizes the environmental impact.

The design of the AWT air conditioners integrates a sleek and modern aesthetic, allowing them to fit seamlessly into any interior environment. Many models feature a compact form that maximizes space utilization without sacrificing performance. For instance, the AWT18F1MBB/BC and AWT20F1MBA models utilize streamlined frames to enhance airflow and circulation.

When it comes to cooling performance, the AWT series excels. With multi-stage cooling technology, these units can provide rapid cooling while maintaining consistent temperatures throughout the room. The AWT24F1MB, for example, showcases a powerful cooling capacity ideal for larger spaces, while AWT24F1MEB/EC caters to users seeking efficient cooling without excessive noise, thanks to its quiet operation mode.

Another significant feature is the advanced air purification systems integrated within these models. The AWT series employs comprehensive filtration technology, which ensures that dust, allergens, and pollutants are effectively removed from the air. Features like the washable and reusable filters contribute to lower maintenance costs and enhanced indoor air quality.

User-friendly functionalities, such as remote control operation and programmable timers, are standard across many units in this series. The AWT20F1MB model, for instance, allows users to set cooling schedules according to their lifestyle, ensuring optimal comfort at all times.

In summary, the Samsung AWT series, comprising models like AWT18F1ME, AWT24F1MB, and AWT20F1MBA, combines energy efficiency, modern design, powerful cooling capabilities, and advanced air filtration systems. These features make the AWT series a compelling choice for customers looking to enhance their living or working spaces with reliable and efficient climate control solutions.