Panasonic CQ-4330U manual Preparation, Dashboard Installation, Installation Hardware

Page 23

Preparation

Warning: If your vehicle is equipped with air bag and/or anti-theft systems, specific procedures may be required for connection and disconnection of the battery to install this product.

Before attempting installation of this electronic component, contact your vehicle dealer or manufacturer to determine the required procedure and strictly follow their instructions.

FAILURE TO FOLLOW THE PROCEDURE MAY RESULT IN THE UNINTENDED DEPLOYMENT OF AIR BAGS OR ACTIVATION OF THE ANTI-THEFT SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY.

Disconnect the cable from the negative battery terminal (see warning and caution below).

Remove Mounting Collar q from the main unit temporarily, which are already mounted at shipment.*

Caution: Various settings that have been stored in the memory in other on-board equipment (vehicle navigation etc.) may be lost if the battery terminals are disconnected.

Therefore, we recommend to make a record of or to back up the settings before disconnecting the terminals.

After completing installation of the main unit, set the equipment again according to the record.

Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30˚.

Dashboard Installation

Installation Opening

This unit can be installed in any dashboard having an opening as shown below. The dashboard should be 3/16” (4.75 mm) – 7/32” (5.56 mm) thick in order to be able to support the unit.

Installation Hardware

No.

Item

Diagram Q’ty

q Mounting Collar*

1

w Plain washer (5mmø)

2

e Spring Washer (5mmø)

2

r Hex. Nut (5mmø)

2

t Rear Support Strap

1

y

Hex. Bolt

1

(5mmø 25 mm)

u

Toothed Lock Washer

1

 

(5mmø)

 

i

Removal Tool

2

 

(U-shaped)

 

o Antenna Connector

1

(a) Using the rear support strap t

 

(b) Using the rubber cushion (option)

Rear support bracket

Rubber cushion (option) (provided on the vehicle)

Mounting bolt (5 mmø)

q Mounting collar

23

CQ-4330U

Image 23
Contents CQ-4330U CQ-4330U Safety InformationFollowing applies only in the U.S.A FCC WarningWhen Parked When DrivingUse the Proper Power Supply When Car WashingContents Mute Power and Sound ControlsPower VolumeBalance Illumination SwitchingBass TrebleInitial Time Clock SettingTime Reset Selecting the Clock DisplayAlarm output Volume Selection Alarm Time SettingInitial Alarm Time Alarm OperationRadio Preset Station Calling Radio Preset Station SettingAuto Preset Memory APM Manual Preset MemoryWeather Band Stations Tuning in a Weather Band StationCassette Tape Player Repeat Play Metal Tape ModeDolby B Noise Reduction Tape Program Search TPS OperationTrack Selection CD Changer modeCD Changer Control Disc SelectionSelect the next available compact disc. Check the disc Error Display MessagesScan Play Tracks Discs Repeat Play Tracks Discs Random PlayChannel Selection XM ModeXM Control Channel ScanSelect a band When the display shows CAT ON, Press 2 Up Press 1 DownPress and hold 1 to 6 for more than 2 seconds to memorize XM ID is communication fails, Press Mode to another mode Press and hold Mode Disp for more than 2 secondsXM Control TroubleshootingPreliminary Steps CommonCassette Tape Sound SettingRadio Wrong MaintenanceSpeaker Connections Product ServicingOverview Installation GuideDashboard Specifications Preparation Dashboard InstallationInstallation Hardware Using the rubber cushion optionExample InstallationMounting springs C Insert each Removal Tool i and pull Removal Tool U-shaped To Remove the Unit from the vehicles dashboardElectrical Connections Wiring DiagramXM Receiver Upgrading the system connect a XM receiverCD Changer CD-DP880, option Upgrading the system connect a CD changerSpecifications One Panasonic Way, Secaucus New Jersey