Panasonic CQ-4330U Metal Tape Mode, Dolby B Noise Reduction, Tape Program Search TPS Operation

Page 13

APM DISP

CLK

PWR BAND MODE

						ALM
			CQ-4330U			LOUD
VOL						MUTE
PUSH						TUNE
SEL/SAT						TUNE
BASS/TREB		DISC	CD SCAN	RPT	RDM	SEEK
BASS/TREB						SCAN
BAL/FADER	1 MTL	2 NR 3 TPS	4 REP	5 SKP	6
	1 MTL	2 NR 3 TPS	4 REP	5 SKP	6

ILL

Metal Tape Mode

Blank Skip

Press [1] (MTL) when playing metal or chromium dioxide (CrO2) tapes.

Press [1] (MTL) again to cancel.

Note: Playing normal tapes in metal tape mode causes high frequency imbalance, which affects tone quality.

Press [5] (SKP) to skip unrecorded portions longer than 15 seconds on the tape.

Press [5] (SKP) again to cancel.

Note: When repeat is on, the blank skip does not work because the repeat has priority over the blank skip.

Dolby B Noise Reduction

Press [2] (NR) to set the Dolby B NR mode. Press [2] (NR) again to cancel.

Note: Set the Dolby B NR mode when playing back a tape recorded with Dolby B Noise Reduction.

Tape Program Search (TPS) Operation

q Press [3] (TPS) to activate the tape program search mode.

w To select a desired program, press [2 TRACK] or [1 TRACK] corresponding times to go forward (up to 9) or backward (up to 8).

	(Rewind:)	(Fast forward:)
8	0	1	9
	c	c

e Press [3] (TPS) again to cancel.

Repeat Play

Press [4] (REP) to repeat the current program.

Press [4] (REP) again to cancel.

Note: The TPS and SKP mode may not work correctly in the following cases. This, however, does not mean that the unit is defective.

•There is an interval less than 3 (15 in SKP mode) seconds or having a high level of noise or hum between programs.

•There is particularly low-level passage during the program.

13

CQ-4330U

Image 13

Contents CQ-4330U Following applies only in the U.S.A Safety InformationFCC Warning CQ-4330UUse the Proper Power Supply When DrivingWhen Car Washing When ParkedContents Power Power and Sound ControlsVolume MuteBass Illumination SwitchingTreble BalanceTime Reset Clock SettingSelecting the Clock Display Initial TimeInitial Alarm Time Alarm Time SettingAlarm Operation Alarm output Volume SelectionRadio Auto Preset Memory APM Radio Preset Station SettingManual Preset Memory Preset Station CallingWeather Band Stations Tuning in a Weather Band StationCassette Tape Player Dolby B Noise Reduction Metal Tape ModeTape Program Search TPS Operation Repeat PlayCD Changer Control CD Changer modeDisc Selection Track SelectionScan Play Tracks Discs Error Display MessagesRepeat Play Tracks Discs Random Play Select the next available compact disc. Check the discXM Control XM ModeChannel Scan Channel SelectionPress and hold 1 to 6 for more than 2 seconds to memorize When the display shows CAT ON, Press 2 Up Press 1 DownSelect a band XM ID is communication fails, Press Mode to another mode Press and hold Mode Disp for more than 2 secondsPreliminary Steps TroubleshootingCommon XM ControlRadio Sound SettingCassette Tape Speaker Connections MaintenanceProduct Servicing WrongDashboard Specifications Installation GuideOverview Installation Hardware Dashboard InstallationUsing the rubber cushion option PreparationMounting springs C InstallationExample Insert each Removal Tool i and pull Removal Tool U-shaped To Remove the Unit from the vehicles dashboardElectrical Connections Wiring DiagramXM Receiver Upgrading the system connect a XM receiverCD Changer CD-DP880, option Upgrading the system connect a CD changerSpecifications One Panasonic Way, Secaucus New Jersey