Panasonic CQ-5330U Alarm Time Setting, Initial Alarm Time, Alarm Operation, Alarm Time Reset

Page 8

Alarm Time Setting

The 12-hour system is used for the clock.

Initial Alarm Time

Press and hold [ALM] (Alarm)

“AM 12:00” is displayed when the alarm is not adjusted.

CLK

PWR

ALM

 

 

 

 

 

 

 

PUSH SEL/SAT

DISP

CQ-5330U

 

 

 

 

LOUD

 

 

 

 

 

VOL

 

 

 

 

 

 

 

 

MODE

 

 

 

 

 

MUTE

 

 

 

 

 

 

 

TUNE

 

 

DISC

 

CD SCAN

RPT

RDM

SEEK

 

BAND

 

 

 

 

 

SCAN

BASS/TREB/BAL/FADER

1

2

3

4

5

6

ILL

APM

 

 

 

 

 

[{TUNE], [}TUNE]

(Hours, Minutes)

Alarm Time Setting

q Press and hold [ALM] (Alarm) and do not release to set alarm time. Display blinks and the alarm time setting mode is activated.

(blink.)

Hours

w Press [{] to set the hour.

(Hours set.)

Alarm Operation

•Alarm is switched to ON or OFF each time [ALM] is pressed.

•When the alarm is switched to ON, the alarm will sound at the set alarm time.

Turning off the Alarm Sound

The alarm will turn off automatically after 90 seconds. Otherwise, press [ALM] once.

Alarm output Volume Selection

You can select ALARM VOL 1 (or VOL 2) by pressing [ALM] in sequence and the display will show as follows.

Minutes

e Press [}] to set the minute.

(Minutes set.)

r Once the alarm time has been set, release [ALM].

Note: Press and hold [{] or [}] to change numbers rapidly.

Alarm Time Reset

When you want to reset the alarm time, repeat steps q to r.

a a OFF

Cautions:

•Be careful not to set wrong alarm time, otherwise, the alarm may sound while driving.

•If the alarm is set, be sure to check the set alarm time by pressing [CLK].

•If volume is set at “0” level, the output volume will be muted. (Even when ALARM is acting.)

8

CQ-5330U

Page 7 Page 9
Image 8
Page 7 Page 9
Contents
CQ-5330U Safety Information Following applies only in the U.S.ALaser Products Wave length 780 nm FCC WarningWhen Driving When Washing Your CarUse Authorized Servicenters When Parked Contents Power and Sound Controls PowerRemote Control Signal Sensor Power on Press PWR powerIllumination Switching BassTreble BalanceClock Setting Time ResetSelecting the Clock Display Initial TimeAlarm Time Setting Initial Alarm TimeAlarm Operation Alarm output Volume SelectionRadio Radio Preset Station Setting Auto Preset Memory APMManual Preset Memory Preset Station CallingTuning in a Weather Band Station Weather Band StationsCD Player Disc Insert and Playback Disc insertStop and Disc Eject Listening to a CDTrack Selection Track Search Repeat play Random play Scan playCD Changer mode CD Changer ControlDisc Selection Track SelectionRemote Control Scan Play Tracks DiscsRepeat Play Tracks Discs Random Play Tracks DiscsXM Mode XM ControlChannel Scan Channel SelectionManual Preset Memory Select a band Press 1 toPress and hold Mode Disp for more than 2 seconds XM ID is or communication fails, Press Mode to another modeCommon TroubleshootingPreliminary Steps Radio Sound Setting XM ControlError Display Messages CD changerCheck the disc Select the next available compact disc. Check the discCare of the Unit MaintenanceCleaning this Unit Speaker Connections Product ServicingWrong ChassisOverview Installation GuideDashboard Specifications Installation Dashboard InstallationInstallation Hardware Using the rubber cushion optionMounting springs C ExampleTabTo Remove the Unit from the vehicles dashboard Insert each Removal Tool i and pull Removal Tool U-shapedCD Receiver Wiring DiagramElectrical Connections XM ANT APM/ PRG Disp VOL Seek Tune Band Mode Specifications GeneralFM Stereo Radio AM RadioMemo Memo One Panasonic Way, Secaucus New Jersey
Top Page Image Contents