Pelco C3468M manual Heavy-Duty In-Ceiling, Tighten the screws until you hear a clicking noise

Page 9

4.Open the hinged door to the back box by pushing the tab lock toward the wall of the unit and lifting the door open.

5.Pull the wiring into the back box through the conduit fitting.

6.Connect all required wiring (refer to Wiring on page 12).

7.Install the back box by compressing the spring clips and pushing the back box through the hole.

8.Tighten the screws until you hear a clicking noise.

HEAVY-DUTY IN-CEILING

1.Prepare the ceiling (refer to Figure 1 on page 8):

a.Locate the center point of the mounting location, and insert the compass tool into the ceiling.

b.Place the end of a pencil in the hole on the end of the compass tool, and draw a circle.

c.Cut out the circle.

2.Use the mounting ring as a template to mark the screw hole pattern onto the mounting surface.

3.Prepare the holes.

Figure 3. Marking the Screw Hole Pattern

4.Install the mounting plates (refer to Figure 4 on page 10). Use the eight 10-32 x 3-inch screws (supplied) to install the mounting ring and the two back mounting plates.

a.Line up the mounting ring with the eight fastener holes.

b.Feed one back mounting plate through the hole in the ceiling. Line up the plate with the four fastener holes.

c.Install fasteners through the mounting ring, ceiling, and out the back mounting plate.

d.Install the second back mounting plate.

C3468M (4/10)

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Spectra IV IP Series SD4E Dome System Page Contents List of Illustrations List of Tables Legal Notice Important NoticesRegulatory Notices Open Source Software NoticeParts List DescriptionModels IN-CEILING MountingPrepare the ceiling refer to Figure Cut out the circleTighten the screws until you hear a clicking noise HEAVY-DUTY IN-CEILINGPrepare the ceiling refer to on Prepare the holesInstalling the Heavy-Duty In-Ceiling Back Box Attaching the Pendant Back Box to the Mount PENDANT, HEAVY-DUTY PENDANT, and Stainless SteelBack Box Door WiringBack Box Circuit Board Connect the Wiring to the Circuit Board Line-In Audio Twisted Pair Cable Speaker Microphone Line-Out Audio Twisted Pair Cable AmplifierClose the interconnect door and snap the tab lock into place Cable requirements Ohm impedance All-copper center conductor Table A. Video Coaxial Cable RequirementsInstalling the Dome Drive Installing the Lower Dome HEAVY-DUTY IN-CEILING Attach the back box leash to the lower dome refer to Figure PendantAttach the back box leash to the lower dome refer to on HEAVY-DUTY PendantC3468M 4/10 Stainless Steel Installing the Stainless Steel Lower Dome Troubleshooting Lower the speaker volume Table C. Troubleshooting the Spectra IV IP Dome System 2Have built-in echo Cancellation Audio is received Too highSwitch Settings Switch Setting Table E. Switch Settings for SW1, Pelco P-Type ControlTable F. Switch Settings for SW1, Pelco D-Type Control Switch Setting Switch Setting Switch Setting Switch Setting Switch Setting 243 244 245 246 247 248 249 250 251 252 253 254 Specifications ElectricalAudio Hours after power-up IN-CEILINGMinimum HEAVY-DUTY IN-CEILING Pendant HEAVY-DUTY Pendant Stainless Steel Power-upConstruction Back Box Dome Drive Aluminum, thermoplastic Lower Dome Trim RingProduct Warranty and Return Information

C3468M specifications

The Pelco C3468M is a sophisticated surveillance camera designed to meet the growing demands of modern security applications. Known for its exceptional image quality and advanced technologies, this camera is an ideal choice for both indoor and outdoor environments.

One of the main features of the C3468M is its high-definition resolution. It delivers stunning 4MP video quality, ensuring that every detail is captured with precision. This clarity becomes invaluable in critical situations where identifying faces or license plates is essential. The camera utilizes advanced imaging technologies, such as Wide Dynamic Range (WDR), which helps balance lighting conditions in complex environments. This means it can effectively capture scenes with both bright and dark areas, making it suitable for diverse lighting situations.

Another notable characteristic of the C3468M is its innovative low-light performance. The camera is equipped with a high-sensitivity sensor, allowing it to produce clear images even in challenging low-light conditions. This is particularly important for surveillance during nighttime or in dimly lit areas, providing round-the-clock monitoring without compromising image clarity.

The C3468M also boasts robust environmental resilience. With an IP66 rating, this camera is protected against dust and water, making it suitable for outdoor applications in various weather conditions. Additionally, it features an IK10 rating for impact resistance, ensuring that it can withstand physical impact and tampering, which is essential for maintaining security in vulnerable locations.

Moreover, the C3468M incorporates advanced video analytics capabilities. Features such as motion detection, tampering detection, and line crossing can be configured to trigger alerts, enhancing situational awareness. These smart capabilities help security personnel respond more effectively to incidents, streamlining vigilance efforts.

The camera is user-friendly, with seamless integration into existing security systems. It supports various connectivity options, including IP networking, allowing for flexible installation and remote access for monitoring. The Pelco C3468M highlights a commitment to security innovation, providing professionals with the tools needed to create safer environments. With its blend of high-performance features and cutting-edge technology, this camera is a reliable choice for comprehensive surveillance solutions.
Top Page Image Contents