Pelco ES31PC, ES30PC manual Important Safety Instructions

Page 5

Important Safety Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

6.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

7.Only use attachments/accessories specified by the manufacturer.

8.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

9.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power- supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

10.Installation should be done only by qualified personnel and conform to all local codes.

11.Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.

12.Use only installation methods and materials capable of supporting four times the maximum specified load.

13.Use stainless steel hardware to fasten the mount to outdoor surfaces.

14.To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant around the bolt holes between the mount and mounting surface.

15.AN ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of the building.

16.A readily accessible disconnect device shall be incorporated in the building installation wiring.

CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other that contained in the operating instructions unless you are qualified to do so.

Only use replacement parts recommended by Pelco.

After replacement/repair of this unit’s electrical components, conduct a resistance measurement between the line and exposed parts to verify the exposed parts have not been connected to the line circuitry.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

WARNING: HAZARDOUS MOVING PARTS. KEEP FINGERS AND OTHER BODY PARTS AWAY.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

C311M-N (6/06)

5

Image 5
Contents ES30PC/ES31PC Esprit with Pressurized IOC Page Contents List of Tables Important Safety Instructions Radio and Television Interference Regulatory NoticesModel Format Pedestal Mount Wall Mount DescriptionModels ES30 ES31 Installation24 VAC 120/230 VACAUX2 Schematic Drawing C311M-N 6/06 HOW to Reinstall the PAN and Tilt Cover TXB Series Translator Board Installation OptionalHOW to Remove the PAN and Tilt Cover TOP Gasket Front Rain Guard HOW to Operate Your System POWER-UP DisplayOperation Operating NotesPressurized Integrated Optics Cartridge Controller Pan Tilt Current Reading MenuZones Programming ES30PC16/ES31PC16 Iris Close CancelProgramming ES30PC22/ES31PC22 Programming ES30PCBW24/ES31PCBW24 Programming Accessing Main Menu PresetMPT9500 KBD4000/KBD4002/KBD4000VWS5050 VCD5000Main Menu ACK ACT Acknowledge ActionAlert Display Position Alert Repeat Auto Focus Mode Auto Iris Auto IR Level Models ES30PCBW24/ES31PCBW24 Auto Sharpness AZ/EL AZ/EL Line Azimuth Zero There are two backlight compensation modes Backlight CompensationDirection Direction Line Display Duration Gain Limit GAIN/AGCIR Filter Mode Models ES30PCBW24/ES31PCBW24 Limit Stops PresetsClear Manual Stops Limit Stops MenuClear Scan Limit Stops Line Synchronization 2 second 8 second Park Time Minutes Pattern Length POWER-UP Mode Proportional PAN Reset Camera Scan Speed Sharpness Shutter Speed Speed Profile White Balance Wiper Mode Zone Blank ZonesZoom Zoom Limit Zoom Line Troubleshooting Symptom Problem Wiper MaintenanceRemoving the IOC Pressurized IOCAppendix Switch SettingSwitch Setting SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 Table B. Switch Settings for SW2 112 234 Electrical SpecificationsFocus Product Warranty and Return Information ISO9001

ES31PC, ES30PC specifications

The Pelco ES31PC and ES30PC are part of Pelco's advanced camera series, designed specifically for security and surveillance applications. These models incorporate state-of-the-art technology to ensure high-quality video performance, versatility, and reliability.

The ES31PC is equipped with a 1/2.8-inch sensor that delivers exceptional image quality, even in low-light conditions. With its ability to capture video in full HD resolution at 1080p, this model assures clarity and detail essential for risk management and security monitoring. The advanced low-light technology enables this camera to perform effectively with minimal illumination, ensuring that critical moments are captured regardless of lighting conditions.

On the other hand, the ES30PC utilizes a similar sensor but emphasizes a compact and lightweight design, making it ideal for discreet installations. This camera also supports full HD video resolution and incorporates advanced image processing techniques to enhance video clarity and reduce noise, providing crisp images in various environments.

Both models feature H.264 and H.265 video encoding, which allows for efficient bandwidth management. This technology optimizes storage space without compromising video quality, making these cameras a cost-effective solution for longer recording times. The integration of Power over Ethernet (PoE) simplifies installation and reduces cable clutter by allowing both power and data to run over a single Ethernet cable.

In terms of connectivity, the Pelco ES31PC and ES30PC support multiple streaming capabilities, ensuring that users can access live feeds remotely via various devices. The built-in web interface provides easy configuration and management options, allowing users to customize settings according to their specific needs.

Additional features include motion detection, which triggers alerts and recording as soon as activity is detected, and a robust weather-resistant housing that allows for outdoor deployment in challenging environments. This combination of durability and high performance ensures that the ES31PC and ES30PC are suitable for a wide range of applications, from retail and commercial spaces to critical infrastructure.

In summary, the Pelco ES31PC and ES30PC surveillance cameras stand out for their superior technology, comprehensive features, and adaptability. These models provide exceptional image quality, efficient video encoding, and user-friendly management, making them reliable options for contemporary surveillance needs.