Pelco ES30PC, ES31PC manual Wiper Mode

Page 54

WIPER MODE

MAIN MENU

 

Wiper Menu

<Camera>

 

Wiper Mode

Momentary

<Line Sync>

 

Wiper Dwell <s>

2

<Power Up>

 

Wiper Time <m>

60

 

 

 

Exit

 

<Wiper>

 

 

<Limit Stop>

 

 

 

<Alert>

 

 

 

<Other>

 

 

 

ACK Alert

 

 

 

Exit

 

 

 

There are three wiper settings:

Wiper Mode (Momentary or Continuous)

Wiper Dwell

Wiper Time

To change the wiper settings:

1.Program preset 95 (28). The main menu appears.

2.Position the cursor (>) beside Wiper.

3.Press the Iris Open button to enter the Wiper menu.

4.Move the joystick up or down to position the cursor next to one of the wiper settings.

5.Press the Iris Open button. The cursor moves to the right.

6.Move the joystick up or down to toggle between through the choices.

7.SELECT: Press the Iris Open button on your keyboard to select your choice.

CANCEL: Press the Iris Close button if you do not want to change the setting.

To operate the wiper feature do the following:

Momentary Mode: To operate the wiper one full cycle, press the AUX 1 button on your controller. Each press of the button operates the wiper one full cycle, even if the AUX 1 button is latching. If AUX 1 is latching, the first press will activate the wiper (open the latch). Pressing AUX 1 a second time closes the latch, but will not cycle the wiper. Press the AUX 1 key again to cycle the wiper.

Continuous Mode: To operate the wiper press the AUX 1 button on your controller. The wiper will continue to operate until the AUX 1 button is pressed again or until the programmed cycle is completed.

NOTE: CM9740 and CM9760 Matrix Systems Only – For the wiper to operate in continuous mode, the AUX 1 function in the camera file must be set to latching. If the AUX 1 camera file is not latching, the wiper will only operate in momentary mode, even if the Esprit wiper is programmed for continuous operation. Refer to the operation manual supplied with the CM9740 or CM9760 matrix system for instructions.

Wiper Dwell: The time between wiper cycles. The dwell time can be programmed from 2 to 30 seconds.

Wiper Time: The length of the wiper cycle. Wiper time can be programmed from 60 to 1,440 minutes (1 to 24 hours).

54

C311M-N (6/06)

Image 54
Contents ES30PC/ES31PC Esprit with Pressurized IOC Page Contents List of Tables Important Safety Instructions Regulatory Notices Radio and Television InterferenceDescription ModelsModel Format Pedestal Mount Wall Mount Installation ES30 ES31120/230 VAC 24 VACAUX2 Schematic Drawing C311M-N 6/06 TXB Series Translator Board Installation Optional HOW to Remove the PAN and Tilt CoverHOW to Reinstall the PAN and Tilt Cover TOP Gasket Front Rain Guard Operation POWER-UP DisplayHOW to Operate Your System Operating NotesPressurized Integrated Optics Cartridge Current Reading Menu Controller Pan TiltZones Iris Close Cancel Programming ES30PC16/ES31PC16Programming ES30PC22/ES31PC22 Programming ES30PCBW24/ES31PCBW24 Accessing Main Menu Preset ProgrammingWS5050 KBD4000/KBD4002/KBD4000VMPT9500 VCD5000ACK ACT Acknowledge Action Main MenuAlert Display Position Alert Repeat Auto Focus Mode Auto Iris Auto IR Level Models ES30PCBW24/ES31PCBW24 Auto Sharpness AZ/EL AZ/EL Line Azimuth Zero Backlight Compensation There are two backlight compensation modesDirection Direction Line Display Duration GAIN/AGC Gain LimitIR Filter Mode Models ES30PCBW24/ES31PCBW24 Presets Limit StopsLimit Stops Menu Clear Manual StopsClear Scan Limit Stops Line Synchronization 2 second 8 second Park Time Minutes Pattern Length POWER-UP Mode Proportional PAN Reset Camera Scan Speed Sharpness Shutter Speed Speed Profile White Balance Wiper Mode Zones Zone BlankZoom Zoom Limit Zoom Line Troubleshooting Symptom Problem Maintenance WiperPressurized IOC Removing the IOCSwitch Setting Switch Setting SW1-4 SW1-5 SW1-6 SW1-7 SW1-8Appendix Table B. Switch Settings for SW2 112 234 Specifications ElectricalFocus Product Warranty and Return Information ISO9001

ES31PC, ES30PC specifications

The Pelco ES31PC and ES30PC are part of Pelco's advanced camera series, designed specifically for security and surveillance applications. These models incorporate state-of-the-art technology to ensure high-quality video performance, versatility, and reliability.

The ES31PC is equipped with a 1/2.8-inch sensor that delivers exceptional image quality, even in low-light conditions. With its ability to capture video in full HD resolution at 1080p, this model assures clarity and detail essential for risk management and security monitoring. The advanced low-light technology enables this camera to perform effectively with minimal illumination, ensuring that critical moments are captured regardless of lighting conditions.

On the other hand, the ES30PC utilizes a similar sensor but emphasizes a compact and lightweight design, making it ideal for discreet installations. This camera also supports full HD video resolution and incorporates advanced image processing techniques to enhance video clarity and reduce noise, providing crisp images in various environments.

Both models feature H.264 and H.265 video encoding, which allows for efficient bandwidth management. This technology optimizes storage space without compromising video quality, making these cameras a cost-effective solution for longer recording times. The integration of Power over Ethernet (PoE) simplifies installation and reduces cable clutter by allowing both power and data to run over a single Ethernet cable.

In terms of connectivity, the Pelco ES31PC and ES30PC support multiple streaming capabilities, ensuring that users can access live feeds remotely via various devices. The built-in web interface provides easy configuration and management options, allowing users to customize settings according to their specific needs.

Additional features include motion detection, which triggers alerts and recording as soon as activity is detected, and a robust weather-resistant housing that allows for outdoor deployment in challenging environments. This combination of durability and high performance ensures that the ES31PC and ES30PC are suitable for a wide range of applications, from retail and commercial spaces to critical infrastructure.

In summary, the Pelco ES31PC and ES30PC surveillance cameras stand out for their superior technology, comprehensive features, and adaptability. These models provide exceptional image quality, efficient video encoding, and user-friendly management, making them reliable options for contemporary surveillance needs.