American Standard 4210 Check Connections for Leaks, Service, HOT Limit Safety Stop Adjustment

M 9 6 8 4 6 1 B

5 CHECK CONNECTIONS FOR LEAKS.

Move HANDLE down into "off" position.

Turn on water supplies and check connections for leaks.

Operate HANDLE (2) up and down, left and right to flush water lines thoroughly.

Operate HAND SPRAY and check connections for leaks.

CHECK CONNECTIONS

FOR LEAKS

6 SERVICE

If faucet drips, operate HANDLE several times from "off" to "on." Do not apply excessive force.

Clogged CARTRIDGE outlets or inlets may cause reduced flow. To clean, first turn off water supply then:

RED

Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3). Pull off ESCUTCHEON CAP (4). Unscrew three MOUNTING SCREWS (5).

Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8). Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).

Place SEALS (8) into CARTRIDGE PORTS (6A).

Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING SCREWS (5) alternately.

2 3

1 4

Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE SCREW (1) and install INDEX BUTTON (2).

HOT LIMIT SAFETY STOP ADJUSTMENT

By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP.

Remove HANDLE BUTTON (1) and loosen SET SCREW (2). Pull
HANDLE (3) off valve stem. Pull off CAP (4). Use a flat blade
screwdriver or your fingers to pull up and rotate red HOT LIMIT
SAFETY STOP (5). Follow Step "A" or "B" to adjust min./max.
discharge temperature. "0" being the hottest to "7" the coldest	"A"
temperature setting. Factory set at "0".

5

6

6A 8

7

		PRY RED RING FORWARD
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten		AND ROTATE COUNTER-
		CLOCKWISE ONE CLICK
HANDLE SCREW (1) and install INDEX BUTTON (2).
			"A"	"A"
TEMPERATURE
			0	ADJUSTMENT WHEN
SETTING NUMBERS			1
			2	WATER IS TOO HOT
			4
"B"			3
			5
PRY RED RING FORWARD			6	6
			7
AND ROTATE CLOCKWISE	"B"
"B"
ADJUSTMENT WHEN				5
WATER IS TOO COLD

"RED RING"- HOT LIMIT SAFETY STOP

7 CARE INSTRUCTIONS

To keep your new faucet looking new, please follow these simple care instructions:

DO: Simply rinse the faucet clean with clear water. Dry the faucet with a soft cotton cloth.

DO NOT:

Do not use any abrasive cleaners, cloths, or paper towels.

Do not use any cleaning agents containing acids, polish abrasives, or harsh cleaners or soaps.

Regular and routine cleaning will reduce the need for heavy cleaning and polishing. If heavy cleaning is required, the following procedures are recommended:

Remove as much surface dirt and film using clear water and soft cotton cloth (as described).

Use any of the following to remove tough surface film and build-up:

Mild liquid detergents

Clear ammonia free liquid glass cleaners

Non-acidic, non-abrasive gentle liquid or fully dissolved powder cleansers mixed according to manufacturers directions.

Non-abrasive liquid polishers

Once clean, rinse faucet again with clear water to thoroughly remove cleaner or polish and and blot dry

with a cotton cloth.

Failure to follow these care instructions may damage the faucet's finish.